Federal Signal Corporation PA300 Series 690009, Инструкции по установке, обслуживанию и эксплуатации

Страница: 9 / 20

-7- -7-
WARNING WARNING
If wires are shorted to the vehicle If wires are shorted to the vehicle frame or frame or
each other, high current conductors can cause each other, high current conductors can cause
hazardous sparks resulting in electrical fires
hazardous sparks resulting in electrical fires
and molten metal.
and molten metal.
Verify that no short circuit Verify that no short circuits exist before s exist before
connecting to the Positive (+) battery termi- connecting to the Positive (+) battery termi-
nal.
nal.
DO NOT connect this system to the vehicle DO NOT connect this system to the vehicle
battery until ALL other electrical connections battery until ALL other electrical connections
are made and mounting of all
are made and mounting of all components is components is
complete. complete.
Failure to observe this WARNING will result Failure to observe this WARNING will result
in fire, burns and blindness.
in fire, burns and blindness.
d. d. Co Conn nnec ect th t the in e in-l -lin ine fu e fuse seho hold lder er
lead to the negative (hot) battery terminal. lead to the negative (hot) battery terminal.
e. e. C Con onne nect ct tthe he re red w d wir ire t e to t o the he
positive terminal of the battery. positive terminal of the battery.
3-4 3-4.. AIR AIR HOR HORN N PR PRESS ESS-A -AND- ND-HOL HOLD D
MODIFICATION. MODIFICATION.
The unit comes from the factory set so The unit comes from the factory set so that the that the
peak-and-hold sound will be heard when the Selector peak-and-hold sound will be heard when the Selector
switch is set to MANUAL and the vehicle horn ring
switch is set to MANUAL and the vehicle horn ring is is
activated. To change the sound to air horn, merely activated. To change the sound to air horn, merely
move jumpers JU1 and JU2 from the “PEAK” posi-
move jumpers JU1 and JU2 from the “PEAK” posi-
tion on the P.C. board to the “AIR” position (see
tion on the P.C. board to the “AIR” position (see
figure 3-5).
figure 3-5).
3-5 3-5.. RE RELAT LATIV IVE PA LOU E PA LOUDNE DNESS AD SS ADJUS JUSTME TMENT NT..
After the PA300 After the PA300 is completely installed in the is completely installed in the
vehicle, set the Selector vehicle, set the Selector switch to MANUA switch to MANUAL. Depress L. Depress
Figure 3-6. Relative PA Loudness Adjustment. Figure 3-6. Relative PA Loudness Adjustment.
the microphone push-to-talk switch, speak in a the microphone push-to-talk switch, speak in a
normal voice, and adjust the GAIN control for the
normal voice, and adjust the GAIN control for the
desired sound level outside the vehicle. Turn-on the
desired sound level outside the vehicle. Turn-on the
vehicle’s two-way rad vehicle’s two-way radio and adjust the volume t io and adjust the volume to a o a
comfortable listening level inside the vehicle. Then comfortable listening level inside the vehicle. Then
set the Selector switch to RADIO. Stand outside of
set the Selector switch to RADIO. Stand outside of
the vehicle and note the radio rebroadcast loudness.
the vehicle and note the radio rebroadcast loudness.
If the sound volume is too
If the sound volume is too loud or too soft, adjust R11 loud or too soft, adjust R11
through the hole at the bottom of the through the hole at the bottom of the siren (see figure siren (see figure
3-6) to the desired sound level. 3-6) to the desired sound level.
After the adjustm After the adjustment is completed, the loud ent is completed, the loudness ness
of the radio rebroadcast and public address may be of the radio rebroadcast and public address may be
varied with the front varied with the front panel GAIN control. panel GAIN control.
3-6 3-6.. TE TEST STING A ING AFT FTER I ER INST NSTAL ALLA LATIO TION. N.
WARNING WARNING
All effective sirens and horns All effective sirens and horns produce loud produce loud
sounds (120 dB) that may cause permanent sounds (120 dB) that may cause permanent
hearing loss. Always minimize your exposure
hearing loss. Always minimize your exposure
to siren sound and wear hearing protection.
to siren sound and wear hearing protection.
Do not sound the siren indoors or in enclosed
Do not sound the siren indoors or in enclosed
areas where you and others will
areas where you and others will be exposed to be exposed to
the sound. the sound.
After installation; test the After installation; test the electronic siren, electronic siren,
including horn operation, to ensure that it is including horn operation, to ensure that it is operat- operat-
ing properly. ing properly.
After testing is comp After testing is complete, provide a cop lete, provide a copy of this y of this
manual to all operating personnel. manual to all operating personnel.
Figure 3-5. Press and Hold Modification. Figure 3-5. Press and Hold Modification.