Federal Signal Corporation IPX-PB45H Скачать руководство пользователя страница 2

Mounting Instructions for Viper

®

 EXT and IMPAXX

®

 Lightheads

2

IPX-PB45H and IPX-PB45V Mounting Bracket Kits

NOTE:

 For electrical installation instructions, refer to the Installation and Maintenance Instructions packed 

with the IMPAXX or Viper EXT.

Mounting the Light

AIRBAG DEPLOYMENT—Do not install equipment or route wiring in the deployment 
path of an air bag. Failure to observe this warning will reduce the effectiveness of 
the air bag, or potentially dislodge the equipment, causing serious injury or death.

IMPORTANT:

 Plan all cable routing before the installation.

1.

  Select a mounting surface for the bracket and position a bracket on it. Mark the center of the two 

mounting holes.

DRILLING PRECAUTIONS—Before drilling holes, check the area you are drilling 
into to be sure you do not damage vehicle components. All drilled holes should be 
de-burred and all sharp edges should be smoothed. All wire routings going through 
drilled holes should be protected by a grommet or convolute/split loom tubing.

2.

  Use a #21 drill bit to drill two 0.159

"

 holes. 

3.

  Route the wire from the lighthead through the bracket.

DO NOT OVERTIGHTEN SCREWS/NUTS–To avoid damage to the lightheads do not 
overtighten the screws and nuts.

4.

  Mount the lightheads to the end brackets using the hardware supplied with the lightheads. The IPX300 Series 

mounts with the bezel; the IPX600 Series and the Viper EXT mount without the bezel (Figures 1 and 2). 
Remove the two #10-32 Torx screws from the back of the IPX600 before mounting the lighthead.

Figure 1

  IPX300 lighthead attached to horizontal bracket

290A6037B

8613173

IPX300

HARDWARE INCLUDED 

WITH LIGHTHEAD

8613173

#10 TYPE B

SCREWS (4)

USE INNER 0.201" HOLES FOR IPX600.
USE MIDDLE 0.116" HOLES FOR IPX300. 
USE OUTER 0.172" HOLES FOR VIPER EXT.

5.

  Mount the lighthead/bracket assembly to the surface with the #10 Type B screws.

6.

  Repeat steps 1 through 5 for the other side.

Содержание IPX-PB45H

Страница 1: ...cautions and information File these instructions in a safe place and refer to them when maintaining or reinstalling the product Failure to follow all safety precautions and instructions may result in property damage serious injury or death Mounting Bracket for IMPAXX and Viper EXT This publication has instructions for using the IPX PB45H horizontal and IPX PB45V vertical brackets for mounting Impa...

Страница 2: ... de burred and all sharp edges should be smoothed All wire routings going through drilled holes should be protected by a grommet or convolute split loom tubing 2 Use a 21 drill bit to drill two 0 159 holes 3 Route the wire from the lighthead through the bracket DO NOT OVERTIGHTEN SCREWS NUTS To avoid damage to the lightheads do not overtighten the screws and nuts 4 Mount the lightheads to the end ...

Страница 3: ... EXT FEDERAL SIGNAL MODEL IMPAXX IPX312 SERIES A VOLTS 12 UNIVERSITY PARK IL 60484 USA 8613222 IPX300 8613222 TOOTHED LOCKWASHER AND STUD INCLUDED WITH LIGHTHEAD 10 TYPE B SCREWS 4 KEPS NUT INCLUDED WITH LIGHTHEAD Ordering Replacement Parts To order replacement parts please contact your local dealer distributor or Customer Support Federal Signal Corporation Phone 1 800 264 3578 7 a m to 5 p m Mond...

Страница 4: ...which the items were purchased The shipping method The model or part number of the product being returned The quantity of products being returned Drop ship information as needed Any estimate required When you receive your RMA Number Write the RMA number on the outside of the box of returned items Reference the RMA number on your paperwork inside of the box Write the RMA number down so that you can...

Отзывы: