2561351F Rev. F2 0520
2645 Federal Signal Drive, University Park, Illinois 60484
Additional translations available at www.fedsig.com
Traducciones adicionales disponibles en www.fedsig.com
Customer Support 1-800-344-4634+1-708-534-4756, [email protected]
Technical Support 1-800-755-7621+1-708-587-3587, [email protected]
Installation
WARNING - EXPLOSION HAZARD:
Do not install the unit in a hazardous location
if the operating temperature exceeds the atmosphere’s ignition temperature.
Unpacking the Device:
After unpacking the device, examine it for damage and
verify parts. Unit comes with: (1) 225XL or 225XL-N assembled unit with flying
leads. If a part is missing or damaged do not attempt to install and contact Federal
Signal Customer Support.
Changing the Flash Pattern from Flashing (default) to Steady
1. Find and locate J3 mini jumper on the board
2. Switch jumper from flash to steady
Electrical Connections
:
To avoid electrical shock,
do not connect wires when circuits are energized. Wiring
must comply to code in the country of use.
•
24VAC/DC Models:
Connect the red (+) lead to the
positive or the phase (hot) side of the power source
and the black (-) lead to the negative or common side
of the power source.
•
120-240VAC 50/60Hz Models:
Connect the black
lead to the phase (hot) side of the power source and
the white lead to the common (neutral) side of the
power source. If required by local building codes,
the green/yellow lead in the housing is provided for
connection to earth ground.
Mounting the Device:
225XL and 225XL-N
come standard to mount 1/2” NPT threaded pipe. Model 225XL-N (NSF
Certified) must be mounted in a dome up position to resist water and debris accumulation and maintain the NSF
Certification.
To comply with NEC Section 300-14, which requires a minimum of 6" of free conductor at a junction, the pipe used to join
the unit to a splice box should be no longer than 10".
Wall mounting bracket (LHWB) is sold separately and is intended for use with model 225XL only. LHWB is not NSF
Certified and incompatible for use with model 225XL-N.
•
Pipe Mount:
Feed wires through pipe and turn clockwise to tighten. To prevent the connection from loosening, tighten
the fixture to a minimum of 5ft.-lbs. (6.8Nm) after threading onto the pipe.
Testing and Operating:
After installation, test the system to verify each signal operates and establish a program
for periodic testing of the device. Provide copy of these instructions to all operating personnel.
Maintenance and Service
Ordering Replacement Parts and Accessories:
Consult product datasheet online for an updated list of replacement
parts. If your product requires a part that is not available for purchase, your unit must be repaired or replaced.
WARNING - EXPLOSION HAZARD:
Substitution of components may impair suitability for Class I, Division 2 environments.
Technical Assistance:
Contact our technical support team at +1-708-587-3587 or [email protected].
Repair Service:
A return authorization is required. Contact your Authorized Distributor or Federal Signal Customer
Support. Defective products under warranty will be repaired or replaced at Federal Signal’s discretion. Lamp failures
excluded.
Product Returns:
A return authorization is required from Federal Signal prior to returning the product. Contact your
Authorized Distributor for more information or to request a product return.
Steady
Flash
Bottom View
J3 Jumper Location
AC
Beacon
Junction box
(not supplied)
1/2" conduit
(not supplied)
Black to Line
(L or L1)
White to Neutral
(N or L2)
Green/yellow to
Earth (Ground)
Wire nuts
(not supplied)
DC
Beacon
Junction box
(not supplied)
1/2" conduit
(not supplied)
(Black to
Negative
Red to
Positive)
Wire nuts
(not supplied)
