manualshive.com logo in svg

Federal Signal Corporation DCFCB, Руководство по модернизации

Поделиться
Скачать
Federal Signal Corporation DCFCB Скачать руководство пользователя страница 15

15

Installing the Kit

Upgrade Manual 

Federal Signal www.fedsig.com

10.  Remove the outside antenna connector from the bulkhead adapter.
11.  Remove the bulkhead adapter.
12.  Remove the outside antenna cable and old antenna. 
NOTE: You may need a bucket truck and ladder to access the site. For installation 

instructions on the Yagi and Omni Antennas, go to the Federal Signal’s website.

Installing the Kit

To install the one-way to two-way kit:
1.  Install the antenna by using the installation instructions on the Yagi and Omni 

Antennas found on the Federal Signal’s website. (items 41-45).

2.  Install antenna lightning protection (item 22).

Figure 6 Antenna lightning protection

The Rubber ring gasket goes on the inside of the cabinet. The marked text “Antenna” 

points down and “Equipment” points up.
3.  Secure lock washer and nut to the outside.

Figure 7 Lock washer

Содержание DCFCB









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды