background image

6

  

  

Installation and Maintenance Instructions

Model 450E Electronic Horn

•  Any maintenance to the unit MUST be performed by a trained 

electrician in accordance with NEC Guidelines and local codes.

•  Never alter the unit in any manner.
•  The nameplate should NOT be obscured, as it contains 

cautionary and/or other information of importance to 

maintenance personnel. 

•  Provide a copy of these instructions to the Safety Engineer, 

operator(s) and maintenance personnel.

•  File these instructions in a safe place and refer to them when 

maintaining and/or reinstalling the device.

Failure to follow all safety precautions and instructions may result 

in property damage, serious injury, or death.

Unpacking the Horn

After unpacking the horn, examine it for damage that may 

have occurred in transit. If the horn has been damaged, do not 

attempt to install or operate it. File a claim immediately with 

the carrier, stating the extent of the damage. Carefully check all 

envelopes, shipping labels, and tags before removing or discarding 

them. Disposal of all shipping materials must be carried out in 

accordance with national and local codes and standards. If any 

parts are missing, please call Federal Signal Customer Support at 

708-534-4756 or 877-289-3246.

An Overview of the Model 450E

SOUND RESTRICTION — Do not paint the horn. No finish or 

coating is required. Paint may obstruct the sound output, 

reducing the effectiveness of the horn. Failure to heed this 

warning may cause serious injury or death.

The Model 450E is a polarized, high-output, continuous duty, 

indoor/outdoor-rated, electronic horn suitable for use in fire alarm 

systems in public mode applications. It is capable of reproducing 

coded blasts or sustained tones. 

Содержание 450E















Отзывы: