background image

IF 

AND 

CHECK or REPAIR 

Induced   blower  does

not energize

3 Flash code does not come on

1.   Induced blower wiring. 
2.   Induced blower. 

Induced   blower  does 

not energize 

3 Flash  code  does   come on

1.

Pressure switch stuck closed. 

2.

Pressure switch is mis-wired or jumpered. 

Induced  blower  is 

energized 

2 Flash  code does not  come o n Wait for the pre-purge to expire. 

2 Flash  code  

comes on 

Induced blower turns off

1. Pressure 

switch stuck in the open position.

2.

Pressure switch, tubing and wiring.

3.

Obstruction in furnace venting that is preventing proper combustion airflow.

Pre-purge   time  h as

expired 

HSI element  does not  glow r ed

within 10 seconds. 

1.   Broken or damaged HSI element. 
2.   Broken or damaged HSI element leadwires.

HSI element i s glow- 

ing red. 

No   other   visible   control   system 

action

Wait for HSI element warm up time to expire. 

HSI element warm  u p

time  has  expired  a nd

main valve  has  been 

energized. 

Main valve  does not  light  within 

trial for ignition period

1.   Induced blower moving main burner gas away from the HSI element. 
2.   Inlet gas pressure too low for main burner ignition. 
3.   Input line voltage too low to heat HSI element.
4.   HSI element incorrectly positioned. 
5.   Clogged or incorrect main burner orifice. 

Main burner 

 lights 

within  trial  for ignition 

period. 

Main valve  i s   de-energized a t the

end of the trial for ignition period. 
If  main flame i s not  sensed  during 

trial for ignition, system will shut  o ff

HSI element  and  main  gas  flow, 

then g o through another purge 

period and initiate another  ignition 

trial. A   total o f 4 ignition  trials  will

be   attempted  before   the system

goes into lockout. 

1.   Line voltage to L1 terminal of integrated furnace control must be 

120 volts with reference to furncace chassis.

2.   Furnace must be reliably connected to earth ground. 
3.   Induced blower moving main burner flame away from the flame sensor rod. 
4.   Inlet gas pressure too low for proper flame sensing. 
5.   Flame sensor rod contaminated or in incorrect position. 

Main  burner stays  o n

after  the  end  of t he

trial  for ignition p e-

riod. 

Circulating fan is not  turned on  after 

30-second time delay. 

1.   Wiring between system control and integrated furnace control.

Proper operation of integrated furnace control.

Main  burner  goes  o ut

before  thermostat  call 

for heat ends. 

4 Flash code comes on

1.  
2.  

Open high limit switch.
High limit wiring in good condition and securely connected.

Main  burner  goes  o ut

before  thermostat  call 

for heat ends. 

4 Flash code does not come on

Green LED off

1.   Induced blower moving main burner flame away from flame sensor rod.

3.  

Pressure switch has opened.

1. 
2. 

Open flame rollout switch
Rollout switch wiring in good condition
Broken or damaged blower

4.  

Flame sensor rod ceramic or leadwire overheated.
Gas supply / flow reduced or interrupted.

5 Flash  code   comes 

on.

TABLE 10 : GENERAL TROUBLESHOOTING INTEGRATED FAN CONTROL

42

3. 

2.  

2.  

Содержание FV95A054



















































Отзывы: