FCI FLT93B, Инструкция по установке, эксплуатации и обслуживанию

Страница: 9 / 106

FLT
®
Series FlexSwitch
TM
GENERAL
Fluid Components International LLC 3
The above typical service power selections are for reference only. De-
pending on application requirements, surface temperature rating require-
ments, and rangeability expectations, alternate power selections may be
recommended. Other intermediate power selections can be made.
ƒ
Relay Rating
Standard: Dual alarm, SPDT or single alarm DPDT field
configurable, 6 amps resistive load at 240 VAC, 120 VAC, 24 VDC.
Optional: Dual alarm SPDT or single alarm DPDT field configurable
hermetically sealed relay, 0.5 amps at 115 VAC/2 amps at 28 VDC.
ƒ
Electrical Enclosure
Aluminum (epoxy coated) or optional stainless steel. Enclosures are
rated for hazardous location use (Class I and II, Division 1 and 2,
Group B, C, D, E, F and G; and EEx d IIC) and weather and corrosion
resistant (NEMA and CSA Type 4X and equivalent to IP66).
ƒ
Operating Temperature
Ambient -40 °F to +140 °F [-40 °C to + 60 °C]
For Flow Service
ƒ
Setpoint Range
Models S, B
Water-based Liquids:
0.01 FPS to 0.5 FPS [0.003 MPS to 1.52 MPS] with 0.75 watt heater;
0.01 FPS to 3.0 FPS [0.003 MPS to 0.9 MPS] with 3.0 watt heater.
Hydrocarbon-based Liquids:
0.01 FPS to 1.0 FPS [0.003 MPS to 0.3 MPS] with 0.75 watt heater;
0.01 FPS to 5.0 FPS with [0.003 MPS to 1.5 MPS] with 3.0 watt heater.
Air/Gas:
0.25 SFPS to 120 SFPS [0.08 NMPS to 37 NMPS] with 0.75 watt heater
at standard conditions; 70 °F [21.1 °C], 14.7 psia [1.013 bar(g)].
Other Fluids: Contact the factory for approximate rangeability.
Model F
Air/Gas:
0.25 SFPS to 120 SFPS [0.08 NMPS to 37 NMPS] 0.25 watt heater
at standard conditions; 70 °F [21.1 °C], 14.7 psig [1.013 bar(g)].
Model L
Water-based Liquids: 0.015 cc/sec to 50 cc/sec
Hydrocarbon-based Liquids: 0.033 cc/sec to 110 cc/sec
Air/Gas: 0.6 cc/sec to 20,000 cc/sec
Model C
Water-based Liquids: 0.01 FPS to 3.0 FPS [0.003 MPS to 0.9 MPS]
Syrup: to 5.0 FPS [0.0003 MPS to 1.5 MPS]
Air/Gas: 0.25 SFPS to 120 SFPS [0.08 NMPS to 36.6 NMPS]
ƒ
Factory Calibrated Switch Point Accuracy
Any flow rate within the instrument flow range may be selected as a
setpoint alarm. A factory-calibrated setpoint adjustment may be
optimally preset with accuracy of ±2% of setpoint velocity over an
operating temperature range of ±50 °F [±28 °C].
ƒ
Monitoring Accuracy
Based on the non-linear output voltage (P1, pins 1 & 2) over the en-
tire flow range, a 100 °F (56 °C) max. temperature span, and a max.
operating pressure range of ±100 psig [±7 bar(g)]:
Liquids: ±5% reading or ±0.04 SFPS [±0.012 NMPS], whichever is larger.
Gases: ±5% reading or ±2 SFPS [±0.61 NMPS], whichever is larger.
ƒ
Repeatability
±0.5% reading
For Level/Interface Service
ƒ
Accuracy
Models S, B
±0.25” [±6.4 mm]
Model F
±0.1” [±2.5 mm]
ƒ
Repeatability
Models S, B
±0.125” [±3.2 mm]
Model F
±0.05” [±1.3 mm]
For Temperature Service
ƒ
Accuracy
±2.0 °F [±1 °C] with field setpoint adjustment. Monitoring accuracy
±3.5 °F [±2 °C] with standard curve fit output voltage operation
across the selected instrument temperature range. Higher accuracy
available with factory calibrations.
ƒ
Repeatability
±1.0 °F [±0.6 °C]
The above accuracy is based on liquid or slurry service and in gas service
with a minimum 1 SFPS [0.3 NMPS] velocity past the sensing element or
with the heater deactivated for temperature sensing service only.
ƒ
SIL: SIL-2 compliant, safe failure fraction (SFF) 82% to 84%
Factory Application-Specific Setup and Setpoint Calibration
Standard instrument factory default settings (unless otherwise
selected at order entry):
• 120 VAC input power for all domestic units.
• 230 VAC for all other agency approval units. Field selectable.
• Dual SPDT alarms set for:
Alarm No. 1 : Preset for flow or level and to de-energize with
decreasing conditions.
Alarm No. 2 : Preset to de-energize for increasing temperature at
10 °F [5 °C] below the maximum instrument process temperature.
• Heater power at 0.25 watt on Model F or 0.75 watt on Model S/B.
• Mode switch set to “operate”.
Factory calibration including set up for specific service, process fluid
and alarm conditions optionally available. Contact factory for fluid
handling capabilities.
Agency Approvals
FM, FMc XP, Class I, Division 1, Groups B, C, D
DIP, Class II/III, Division 1, Groups E, F, G
T4, Ta = 60 °C; T3A, Ta = 60 °C
ATEX II 2 G Ex d IIC T6...T2 -40 °C to 60 °C Gb
IECEx Ex d IIC T6 or T5
Tamb (Housing) = -40 °C to 40 °C, T6
Tamb (Housing) = -40 °C to 60 °C, T5
Tp (Sensing Element) = -40 °C to 77 °C, T4
Tp (Sensing Element) = -40 °C to 177 °C, T2
Other Certifications : SIL-2 rated, CRN, probe complies with Cana-
dian Electrical Code requirements of ANSI/ISA 12.27.01-2011 as a
single seal device, CE marking, RoHS2 compliant
Shipping Weight (approximate)
Integral: 8 lb [3.6 kg]
Remote: 13 lb [5.9 kg]