Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 22

Страница: 22 / 110

3.3 Basic safety regulations for safe operation

3.3.1 Remaining dangers, remaining risks

Despite careful work and compliance with standards and regula-

tions it cannot be ruled out that further dangers may arise when

working with and handling the machine.

Both the machine as well as all other system components comply

with the currently valid safety regulations. Nevertheless, remaining

risks cannot be ruled out completely, even when using the machine

for the purpose it is intended for and following all information given

in the operating instructions.

A remaining risk can also not be excluded beyond the actual

danger zone of the machine. Persons remaining in this area must

pay particular attention to the machine, so that they can react

immediately in case of a possible malfunction, an incident or failure

etc.

All persons remaining in the area of the machine must be informed

about the dangers that arise from the operation of the machine.

3.3.2 Regular safety inspections

Have the machine inspected by an expert / qualified person as

required for the conditions the machine is working under, but at

least once every year.

3.3.3 Modifications and alterations to the machine

Unauthorized changes to the machine are prohibited for safety rea-

sons.

Original parts and accessories have been specially designed for

this machine.

We wish to make explicitly clear that we have not tested or

approved any parts or accessories not supplied by us.

The installation and/or use of such products may have an adverse

effect on the active and/or passive safety.

3.3.4 Damage, defects, misuse of safety devices

Machines which are not safe to operate or in traffic must be imme-

diately taken out of service and shall not be used, until these defi-

ciencies have been properly rectified.

Safety installations and switches must neither be removed nor

must they be made ineffective.

Concerning your safety – Basic safety regulations for safe operation

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды