Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 108

Страница: 108 / 110

10.1 Final shut-down of machine

After the machine has reached the end of its service life, the indi-

vidual components of the machine must be disposed of properly.

Observe national regulations!

Carry out the following work and have the machine dismantled by a

state-approved recycling company.

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep gasoline away from heat sources, sparks

and other sources of ignition.

–

Do not spill any gasoline.

–

Components that previously contained gaso-

line must not be cut with a cutting torch.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 ‘Han-

dling fuels and lubricants’ on page 23

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Safety goggles

Empty the fuel tank.

Drain engine oil from engine and exciter housing.

Disposal – Final shut-down of machine

DFP8

108

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды