Fayat BOMAG BVP 10/36 Скачать руководство пользователя

Страница: 92 / 112

8.9 As required

8.9.1 Cleaning the cooling fins and the cooling air intake openings

How dirty the cooling fins and cooling air intake

openings are depends very much on the daily

operating conditions; clean daily if necessary.

NOTICE!
Danger of engine damage caused by reduced

cooling!

–

For this reason you should always seal any oil

or fuel leaks in the vicinity of the cooling fan or

the coolers and clean the cooling fins after.

Protective equipment:

Working clothes

Protective gloves

Safety goggles

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 62

Allow the engine to cool down.

Remove dried dirt with a suitable brush from all cooling fins

and cooling air intake openings.

CAUTION!
Danger of eye injuries caused by particles

flying around!

–

Wear your personal protective equipment

(safety gloves, protective working

clothes, goggles).

Blow out the cooling fins and cooling air intake openings with

compressed air.

If the engine is oily, use a cold cleansing agent for cleaning.

Fig. 93

Cleaning with cold cleansing agent

Maintenance – As required

BVP 10/36

Содержание BOMAG BVP 10/36

















































































































Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды

Fayat BOMAG BVP 10/36, Инструкция по эксплуатации

Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды