Installation of Drivers for Windows XP / XPe
VIM301
V I M 3 0 1 U s e r M a n u a l
52
© 2 0 1 5 F a s t w e l v . 0 0 2
APPENDIX A:
DISCLAIMER
This Disclaimer contains special operating conditions of Fastwel in the following areas: intellectual property, warranty
policy, conditions of the order and delivery.
1 INTELLECTUAL PRORETY
1.1 If any infraction, interference, improper use, illegitimate exploitation and/or violation of the industrial and/or intellectual
property rights of any third party and/or property, exploitation during the use of Fastwel Embedded Module will take place
– Fastwel does not guarantee to replace the materials, computer programs, procedures or equipment affected by the
complaint and under no circumstances doesn't bear responsibility in any form for possible refusal in case of such a
replacement.
1.2 Use of the Fastwel products as well as the objects of intellectual property containing in them, in the ways and for the
purposes, not provided by the present user manual and datasheet isn't allowed without preliminary written approval of
Fastwel.
1.3 Fastwel is not responsible for possible incidents and losses, related to the operation of end devices, in which the
original Fastwel equipment is used.
2 WARRANTY POLICY
2.1 When the detected flaws in an element can be corrected without decreasing the foreseen technical features and
functionality for it, User may demand Fastwel the urgent correction of the failures in additionally agreed period and an
increasing of the period of the guarantee of the element equal as the time elapsed from the formal request to repair the
failures, until the receipt of the repaired element. All costs associated to the correction of failures, included those of
assembly, dismantle, transport, tests, etc, if they exist, shall be prosecuted according the Warranty Policy of Fastwel.
3 ORDER AND DELIVERY CONDITIONS
3.1 The general rule is that all Fastwel equipment prices are determined with due consideration of delivery under the
EXW terms and conditions (Incoterms 2010). Delivery of the products under other terms and conditions should be
preliminary agreed and stated in writing between the parties.
3.2 Unless otherwise expressly agreed with Fastwel, all the deliveries of Fastwel equipment will be carried out only after
the official purchase order is obtained and provided that the ordered products have been prepaid in full. Other terms and
conditions of cooperation should be made in writing.
3.3 Any delivery of Fastwel electronics is submitted with the right package in accordance with the current rules and
standards in the Member States of the European Economic Area. The purchaser independently bears all risks regarding
the compliance of package and marking of Fastwel products with legislation requirements being in effect at the place of
purchased products destination (in the buyer’s country). The specified condition excludes unequivocally any liability of
Fastwel for possible non-compliance of package and marking of products with the requirements of legislation of the
country of products destination.
3.4 In general, all components of the supply are properly protected with respect to freight, in order to avoid any damage
to the supply, third parties, environmental damages or unrelated goods, as consequence of wrong packaging.
3.5 Each package unit is labeled on the exterior area with the indications of product’s Part Number and Serial Number.
3.6 The support documents for the order should be made either in English or in Russian unless otherwise agreed
between parties in writing.
3.7 Fastwel does not pay penalties and does not cover costs associated with delay in the delivery of the products caused
by actions of the third parties, force-majeure etc. - Fastwel doesn't bear any responsibility for non-execution or
inadequate execution of the obligations in a case when it is caused by actions of the third parties (for example producers
or suppliers of accessories), force majeure etc.
3.8 Fastwel declares that independently and at any time without damage, it has an exclusive right to define and change
functionality architecture, bill of materials of its products without any preliminary coordination and approvals of the third
parties.
4 OTHER CONDITIONS
4.1 Fastwel has the obligation to respect the current Russian legislation (including, but not limited to environmental,
labor, social laws) in each moment and to apply it to its embedded electronics considering all and each execution phase,
that is to say, from the design until the commissioning and subsequent maintenance. In this regard Fastwel is not liable
to the user or other persons in connection with possible changes of the company’s rules (including, but not limited to
warranty, ordering policy) caused by changes of the Russian legislation.
4.2 Unless otherwise expressly agreed in writing, Fastwel provides no training for
assembly\installation\adjustment\operation of its equipment.
