Fastech Ezi-Step Plus-R Скачать руководство пользователя страница 25

Страница: 25 / 70

www.fastech.co.kr

6. External Name and Function Setting of Ezi-STEP-PR

6.2 Status Display LED

6.3 Drive ID Select Switch(SW1)

When several modules are connected to one daisy chain network, this switch is to

set intrinsic ID to each module.

The switch can set intrinsic ID to each module up to 16 numbers from 0 to F(15).

Position

ID No.

Position

ID No.

6.4 Communication Speed and Terminal Resistance Select Switch (SW2)

SW2 is to set the communication speed between central controller (PC) and Drive. If

corresponding drive module is connected to the end of one network segment, SW2 sets

whether terminal resis tance is used. SW2.1 is to set the use of terminal resistance,

and SW2.2~SW2.4 is to set the communication speed as follows.

The communication speed of drive modules connec ted to one segment must

be set to the same value.

Support max. 115200[bps] when using RS -232 to RS-485 conveter

SW2.1

SW2.2

SW2.3

SW2.4

Baud

rate

[bps]

*1 : default setting value .

SW2.1 is OFF.: Terminator resistor is Off.

SW2.1 is ON. : Terminator resistor is On.

OFF

9600

OFF

19200

OFF

38400

OFF

57600

OFF

115200 *1

OFF

230400

OFF

460800

921600

Caution

Содержание Ezi-Step Plus-R






































































Результаты поиска

Содержание Ezi-Step Plus-R

Отзывы:

Бренды по названию

Популярные бренды

Fastech Ezi-Step Plus-R, Руководство пользователя

Результаты поиска

Содержание Ezi-Step Plus-R

Отзывы:

Бренды по названию

Популярные бренды