Fast 9500 Скачать руководство пользователя страница 85

Страница: 85 / 116

FILLING THE TANK

FILLING THE TANK

Boom Sprayer 9500 / 9600

Page 85

Rotate the directional valve (C) to

direct flow toward the main tank.

Open the agitation valve (D) 1/3 of

the way. Adjust as needed.

Start the pump on the tender truck

and open the valve on the fill line.

Start the

Sprayer pump after the main

tank is at least 1/4-full of water to start
circulation (agitation.)

Pump until the tank is filled to the

desired level. Do not overfill.

Close the input valve to prevent back-

flushing and stop the pump on the

tender truck.

10.

Remove and stow the transfer hose.

11.

Install and fasten the fill line’s covers.

Filling Fresh Water Rinse Tank

Rinse Tank Quick Fill

Main Tank Quick Fill

Rinse Tank

Each machine is equipped with a freshwater

rinse tank (C) on the front of the frame. Fill

the rinse tank with clean freshwater

whenever rinse water has been used. Do not

allow this tank to run low on fresh water.

Use water from the rinse tank to clean, rinse

or, wash anything that has become

contaminated. It should be used at the end of

each working day to flush out the pump and

booms to prevent corrosion.

WARNING: Do not drink the water

from the rinse tank.

The rinse tank water may become

contaminated with sprayer chemicals or

other contaminates.

Use Tank Fill Marker

Fill Marker

The back end of the Product Tank has a fill

marker decal (A) on it to assist the Operator

when filling the tank.

NOTE: The tank must be level for

accurate volume readings. Use the

hydraulic hitch option to raise or

lower the front end of the trailer or

refer to

Adjust Hitch Height

for further

adjustment.

Содержание 9500





















































































































Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды

Fast 9500, Руководство пользователя

Результаты поиска

Содержание 9500

Отзывы:

Похожие инструкции для 9500

Бренды по названию

Популярные бренды