Fast Lift Parts Rol-Lift T Series Скачать руководство пользователя

Страница: 13 / 17

888-999-7715

www.FastListParts.com

Lifting Link

Snap Ring

Traverse

E SERIES

SERIES

Eccentric Pin

Shoulder

Eyebolt

Snap Ring

Pivot Axle

Lifting Link

Shaft

Snap

Ring

Lifting Link

Installation

Turn the jack over so that the undercarriage of the jack facing up, position

the lifting link in the frame. Insert the lifting link shaft and secure it with its

snap ring. Attach the push rod (see Push Rods) and the load roller bracket

(see Load Roller Brackets). Turn the jack upright and install the traverse with

the hydraulic unit and steer wheel assembly still attached (see Traverse).

Position the ram and upper thrust bearing assembly into the A-Frame.

Secure it with the snap ring. (45 minutes)

Bearing

Load Roller

Bracket

Push Rod Axle

Nut

Snap Ring

Steer

Wheel

Axle

Steer

Wheel

Bearing

Содержание Rol-Lift T Series


















Результаты поиска

Содержание Rol-Lift T Series

Отзывы:

Похожие инструкции для Rol-Lift T Series

Бренды по названию

Популярные бренды

Fast Lift Parts Rol-Lift T Series, Руководство по обслуживанию

Результаты поиска

Содержание Rol-Lift T Series

Отзывы:

Похожие инструкции для Rol-Lift T Series

Бренды по названию

Популярные бренды