Faro FaroArm Fusion Скачать руководство пользователя | Manualshive

Страница: 40 / 130

background image

FaroArm

®

Manual

January 2009

32

Chapter 1: Introduction to the FaroArm

®

• Down - as you move the Laser Line Probe farther from your part
• Left - the right side of the line is in range
• Right - the left side of the line is in range

The target box changes color:
• Green - all of the laser is in range
• Blue - some of the laser is in range
• Red - none of the laser is in range

When the Laser Line Probe is outside of the operating range, the target
box moves to a side of the R

ANGE

F

INDER

dialog box and an arrow in

the center of the dialog box points to the target box, see Figure 1-30.

If the Laser Line Probe is set to automatic exposure, there is an
additional symbol in the upper left corner of the R

ANGE

F

INDER

dialog

box. The symbol changes describes the exposure:
• Red Minus Sign (-) - low exposure
• Green Circle (O) - good exposure
• Red Plus Sign (+) - high exposure

For more information, see “Laser Line Probe Settings” on page 40.

Software Setup

The FaroArm/FARO Laser Line Probe system can be used with many
software packages. Refer to the particular application software for
installation and proper use of the software with the FARO Laser Line
Probe.

N

OTE

: Some software packages automatically add the FaroArm

software driver to your computer. To ensure that you have the latest
version of the FaroArm software driver, install the CD-ROM found
inside your FARO Laser Line Probe case.

Calibration

After you complete the installation and warmup of the FARO Laser
Line Probe and the standard probe, this system of probes must be
calibrated. Calibration requires measuring the FARO Calibration Sphere
or FARO Calibration Plate, with the standard probe and the Laser Line
Probe.

N

OTE

: Clean the top and bottom lenses with the cloth from the Laser

Line Probe case. Dirt and grease on either lens can cause poor results.

1 In you measuring software, start the PROBE command.

08M46E00_FaroArmUSB.book Page 32 Tuesday, February 17, 2009 1:42 PM

«
...
38
39
40
41
42
...
»

Содержание FaroArm Fusion



































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaroArm Fusion

Mentor Visual iQ

Бренд: GE Страницы: 2

Бренд: Kawai Страницы: 19

Бренд: Calculated Industries Страницы: 64

Бренд: Eaton Страницы: 43

Бренд: Yamaha Страницы: 84

Бренд: Keeler Страницы: 54

Бренд: LOVATO ELECTRIC Страницы: 10

Бренд: e-sylife Страницы: 2

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Friendly Digital Piano Forte PV35

Бренд: Kawai Страницы: 102

zelsius C5 -IUF

Бренд: Zenner Страницы: 28

Бренд: R&S Страницы: 46

Бренд: General Страницы: 16

Бренд: WIKA Страницы: 52

Бренд: ERICHSEN Страницы: 33

Бренд: Seli Страницы: 68

Бренд: Powerfix Profi Страницы: 93

Бренд: Kawai Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды