Faro FaroArm Fusion Скачать руководство пользователя | Manualshive

Страница: 103 / 130

background image

A-1

Appendix A: Software License

Agreement

This Software License Agreement is part of the Operating Manual for
the product and software System which you have purchased from FARO
TECHNOLOGIES, INC. (collectively, the “Licenser”) By your use of
the software you are agreeing to the terms and conditions of this
Software License Agreement. Throughout this Software License
Agreement, the term “Licensee” means the owner of the System.

I.

The Licenser hereby grants the Licensee the non-exclusive right to

use the computer software described in this Operating Manual (the
“software”). The Licensee shall have no right to sell, assign, sub-
license, rent or lease the software to any third party without the
Licenser’s prior written consent.

II.

The Licenser further grants the Licensee the right to make a backup

copy of the software media. The Licensee agrees that it will not
decompile, disassemble, reverse engineer, copy, transfer, or otherwise
use the software except as permitted by this section. The Licensee
further agrees not to copy any written materials accompanying the
software.

III.

The Licensee is licensed to use the Software only in the manner

described in the Operating Manual. Use of the Software in a manner
other than that described in the Operating Manual or use of the software
in conjunction with any non-Licenser product which decompiles or
recompiles the software or in any other way modifies the structure,
sequence or function of the software code, is not an authorized use, and
further, such use voids the Licenser’s set forth below.

IV.

The only warranty with respect to the software and the

accompanying written materials is the warranty, if any, set forth in the
Quotation/Purchase Order and

Appendix B: Purchase Conditions

pursuant to which the software was purchased from the Licenser.

V.

THIS WARRANTY IS IN LIEU OF OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO
THE SOFTWARE AND WRITTEN MATERIALS. IN NO EVENT

08M46E00_FaroArmUSB.book Page 1 Tuesday, February 17, 2009 1:42 PM

«
...
101
102
103
104
105
...
»

Содержание FaroArm Fusion



































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaroArm Fusion

Бренд: Campbell Страницы: 362

Бренд: Campbell Страницы: 60

Бренд: Campbell Страницы: 116

Бренд: Campbell Страницы: 30

Бренд: Campbell Страницы: 55

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: OHAUS Страницы: 32

Бренд: Hammond Страницы: 78

Бренд: RIDGID Страницы: 18

Бренд: Trotec Страницы: 14

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Бренд: E+E Elektronik Страницы: 20

Бренд: Brooks Страницы: 64

Бренд: brena Страницы: 26

C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1

Бренд: Sierra Страницы: 55

Бренд: Cressi Страницы: 36

Celviano AP-60R

Бренд: Casio Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды