3
2
) HOW TO PROGRAM
THE REMOTE
CONTROL FOR VIDEO
RECORDERS
2.1)
IF YOU KNOW THE BRAND
OF THE VIDEO RECORDER…
N.B. The main functions of the video recor-
der, once the remote control has been pro-
grammed, are accessed by simply pressing
the specific buttons.
2.1.A
) Look at table C page
6-7
relating to
brands and codes for video recor-
ders. Next to the required brand are
listed one or more codes that have
to be inserted, in the same way as
described for TVs from para. “
1.1.B
”,
one at the time, in turn, until the one
that operates your VCR correctly is
found. (See also Note
1
at the end of
para. “
2.2
”).
Should you not be able to find the correct
code for the required brand, or the brand is
not listed, go to the next paragraph.
2.2
) VCRs, AUTOMATIC SEARCH
AND PROGRAMMING
2.2.A
) Insert a video cassette, preferably
blank, and set the video recorder on
STAND BY.
2.2.B
) Point the remote control towards
your VCR.
2.2.C
) Press and release the «
», but-
ton and then press and keep pressed
the «
» (PLAY), button (
∆
Fig.
1
),
Release the button as soon as the
tape starts advancing. (During the
search phase the LED will emit a
series of short flashes).
2.2.D
) Stop the tape and check the workings
of the other buttons (See also
Note
1
).
IF EVERYTHING IS OK! THE REMOTE CON-
TROL IS READY.
We advise you make a note of the code just
memorized following the instructions in
para. “
3
”: Displaying the code.
If some commands do not correspond,
repeat the search procedure. If the tape
does not start advancing within
5
minutes of
commencing the search, see para. “
5
”:
“What to do if…”.
NOTE
1
: the RECORD function is accessed
by pressing simultaneously the «SHIFT»
and «
l
» (orange symbol) buttons.
The OFF or STAND BY functions are acces-
sed by pressing simultaneously the «SHIFT»
and «
» (orange symbol) buttons.
3
) DISPLAYING THE
CURRENT CODE
Premise:
• Each code is composed of
4
digits.
• The LED indicates each digit as the sum of
a series of short flashes, except for the
zero that is represented by one long flash.
• The LED pauses for approx.
2
seconds in
between each digit.
3.1) Press and keep pressed the «SHIFT»
button.
3.2) Press the «
» button.
3.3) Release both buttons («
» and
«SHIFT»).
3.4) Press and release the «
» (OFF) but-
ton for TV or «
» (PLAY) for video
recorders.
Watch the LED which, after a short flash
when pressing the button, will indicate the
code as described in the premise.
4
) LEARNING
FUNCTION
General
GR-9200
can learn from the majority of
remote controls on the market (TV, VCR,
SAT, etc.) up to a maximum of
19
functions.
The commands can be memorized on two
memory banks, selected by using the
«LEARN», button, using all buttons except
«SHIFT», «
», «VT» and «LEARN».
NOTE: the «LEARN» button, to select the
second memory bank, is used when wanting
to learn functions that are additional to
those already in use and all the buttons are
full. It is not necessary to select the second
memory bank if you want to replace com-
mands on buttons that are not in use.
A learned command automatically replaces
any pre-existing preprogrammed command.
If you make a mistake and forget to select
the second memory bank , the original pre-
programmed command can be restored by
simply cancelling the learned command.
In all cases, it is necessary to cancel a lear-
ned command before it can be replaced.
When toggling between memory banks, by
pressing «LEARN», the LED flashes once or
twice, to indicate which one is active, or not
at all if the second is empty.
4.1
) Learning procedure.
a) Place the two remote controls on a level
surface as shown in the figure below.
b) Press and realease the «
» but-
ton and enter the code «
5 5 5 5
». Wait
for the LED to emit 5 short flashes and
then…
c) If necessary, select the memory bank by
pressing the «LEARN» button (See Note
above).
CODE
?
CODE
?
CODE
?
CODE
?
CODE
?
Visa GR-
9200
Original
3
~
5
cm.
N.E. GR 9200 (GB) 13-07-2000 11:57 Pagina 3
