manualshive.com logo in svg

Farmet MONSUN MC, Руководство по эксплуатации

Поделиться
Скачать
Farmet MONSUN MC Скачать руководство пользователя страница 4

 

 

Manual

 

MONSUN MC | ME 

4 

│

 58 

INTRODUCTION    

Get  acquainted  with  the  contents  of  this  operating  manual  before  putting  the  machine  into 
operation or before its installation. In any case, read the safety instructions in the "Safety" chapter 
and follow  the  warning notices in individual chapters. Thus you achieve optimum work  results  and 
safe working. 

The manufakturer Farmet a.s. Ceska Skalice cannot accept any liability for damage or malfunctions 
caused by non-compliance with the instructions given in this manual. 
 
All  persons who  will operate  the  machine  or  perform  following  actions  shall  read  and  observe  the 
operating manual: 

 

operation / including preparation, troubleshooting during operation, maintenance/ 

 

service works and inspections 

 

transport 

With  regard  to  technical  innovations  we  reserve  the  right  to  make  changes  to  the  technical  data 
stated in this operating manual. 

Regulations governing the guarantee 

 

1. 

 

Our  products  are  covered  with  24  month  guarantee  or  with  800  hectares  being  sown  with  the 
machine, starting on the date of the machine delivery to the user. 

The guarantee does not cover:  

 

spare parts subject to wear, 

 

any occurrence of intentional damage, 

 

damage caused by unprofessional operation of the machine, or non-compliance with the 
operating manual, 

 

mechanical damage during transport.  

2. 

 

Claims to warranty repair can only  be made  if the  device  has not  been modified by the user or 
another  person.  In  order  to  acknowledge  the  warranty,  the  nameplate  on  the  control  unit  of 
electronic device must not be damaged. 

3. 

 

During  the  warranty  period,  the  supplier  -  manufacturer  will  remove  for  free  the  defects  and 
malfunctions  caused  by  defective  material,  or  defective  assembly  provided  the  following 
conditions are met: 

- the user of the machine shall notify the supplier - manufacturer in writing of the occurrence 

and  scope  of  defects  and  malfunctions.  Based  on  the  written  notification  the  supplier  - 
manufacturer shall provide the defect removal.  

4. 

 

When claiming the warranty it is necessary to submit the confirmed warranty card and the serial 
number on the warranty card must agree with the serial number of the seed drill. 

5. 

 

The warranty period is prolonged with the repair duration. 
 
 

Regular training 

Instruct workers regularly, or at least once per year, on basic rules of conduct to handle the machine 
in maximum safety. 
 

Training

 

A professional dealer will train you in operation, safe use and basic machine service. Commissioning 
the machine without training is prohibited!  

Содержание MONSUN MC



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды