Farm King TVR12 Скачать руководство пользователя страница 25

Страница: 25 / 112

Assembly - TVR12, TVR14, TVR16 V-Rake

Component Unloading And
Identification

WARNING

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when
assembling the equipment.

WARNING

DO NOT permit bystanders to be in the work area
when unloading and assembling components.

DO NOT work under suspended parts.

Keep away from moving parts.

Always use lifting devices / vehicles, chains
or straps of adequate size and strength when
unloading and assembling components.

Unload the crate(s) and components on a flat level
area of adequate size to assemble the equipment.

IMPORTANT

Unload crate(s) and other components carefully to
prevent damage to any of the components.

NOTE: If any components are damaged, missing

or replacement parts are required, contact
your Farm King Dealer.

Assemble the equipment in the following order on
a flat and level surface:

1. Frame

2. Wings

3. Rakes

Using the packing list, locate and place all
components and hardware in one area. Count the
individual components and verify that you have
received the correct number of components to
fully assemble the equipment.

IMPORTANT

The directions front, left, right, and rear are viewed
as the operator sitting in the operator’s seat with
the equipment hitched to the tractor.

Содержание TVR12

















































































































Результаты поиска

Содержание TVR12

Отзывы:

Farm King TVR12, Руководство оператора и каталог запасных частей, Страница: 25 / 112

Результаты поиска

Содержание TVR12

Отзывы: