Farm King Model 1050 Скачать руководство пользователя страница 65

Страница: 65 / 174

Operation - 10" Backsaver Auger

GENERAL OPERATION INFORMATION

Pre - Operation Checklist

Before operating the Backsaver Auger for the first

time and each time thereafter, check the following

items:

1. Lubricate the equipment per the schedule outline in

the Maintenance Section. (See “SERVICE

SCHEDULE” on page 88.)

2. Check the Backsaver Auger’s hitch for damaged,

loose or missing parts. Repair as needed before

operation.

3. Check tire pressure. Inflate per manufacturer’s

specification.

4. Check wheel bolts for tightness. Torque as

required. (See “AXLE” on page 93.)

5. Check the augers. Remove any material build-up or

debris that has become entangled.

6. Check that all bearings turn freely. Replace as

required.

7. Make sure that all guards and shields are in place,

secured and functioning as designed.

8. Check condition of all hydraulic components for

leaks. Repair as required.

NOTE: Do not operate with hydraulic leaks.

9. Check gearbox oil level. Fill as required. (See

“LUBRICATION” on page 89.)

10. Verify that the tractor’s drawbar is adjusted

correctly for use with the auger. (See “Drawbar

Adjustment” on page 65.)

11. Check that the PTO driveline telescope easily and

turn freely.

12. Make sure the PTO ends are securely attached to

the auger and the tractor.

AVOID INJURY OR DEATH

•

Disengage the PTO, engage the machine’s parking

brake, stop the engine and make sure all rotating

components are completely stopped before

connecting, disconnecting, adjusting or cleaning

any PTO driven equipment.

•

Always keep PTO shields and all guards in place

when using PTO driven equipment.

•

Disengage PTO for road travel.

•

Keep hands, feet and clothing away.

AVOID INJURY OR DEATH

Wear safety glasses to prevent eye injury when any

of the following conditions exist:

•

When fluids are under pressure.

•

Flying debris or loose material is present.

•

Engine is running.

•

Tools are being used.

Leaking fluids under pressure can enter the skin and

cause serious injury or death. Immediate medical

attention is required. Wear goggles. Use cardboard to

check for leaks.

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Бренды по названию

Популярные бренды