Farm King Model 1050 Скачать руководство пользователя страница 28

Страница: 28 / 174

Assembly - 10" Backsaver Auger

BASE GROUP

Undercarriage Assembly

Assemble the undercarriage on a flat level surface.

Figure 4

Install a strap (Item 1) around the center of the axle

(Item 2)

[Figure 4]

Connect the strap to an approved lifting device.
Raise and move the axle to the assembly area.
Lower the axle to the ground and remove strap.

Figure 5

Align the hub (Item 1)

[Figure 5]

with the axle.

Install the four 1/2” x 1-3/4” bolts (Item 2)

[Figure 5]

and 1/2” lock nuts. Tighten bolts and nuts.

Install a strap around the center of the right

undercarriage arm.
Connect the strap to an approved lifting device.
Raise and move the left undercarriage arm towards

the axle.

•

DO NOT permit bystanders to be in the work area

when unloading and assembling the auger

components.

•

DO NOT work under suspended parts.

•

Keep away from moving parts.

•

Always use lifting devices / vehicles, chains or

straps of adequate size and strength when

unloading and assembling the auger components.

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when

assembling the equipment.

B-0583

B-0586

Содержание Model 1050















































































































































































Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды

Farm King Model 1050, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Model 1050

Отзывы:

Похожие инструкции для Model 1050

Бренды по названию

Популярные бренды