manualshive.com logo in svg

Farm King BW200, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Farm King BW200 Скачать руководство пользователя страница 37

Operation - 200 Bale Wrapper

35

Drive Chain Adjustment

Figure 19

Two chain transmissions are used in this bale 
wrapping machine. After wrapping the first ten 
bales, the tensioning of the drive chains needs to 
be adjusted.

Remove the chain cover (Item 1). Loosen the four 
M12 nuts (Item 2). Turn the M12 screw in the chain 
tightening mechanism (Item 3) so that the chain 
has a 20 mm slack after tightening 

[Figure 19]

. 

Tighten the four M12 screws (Item 2). Install the 
chain cover 

[Figure 19]

.

IMPORTANT

Check the tightening and the chain condition 
periodically after wrapping every 120 bales.

3

1

FINISHING WORK

After the work is complete, disconnect the 
revolution counter and secure the revolution 
sensor against humidity.

Before storing the wrapping machine for a longer 
period, place the impulse sensor in a dry storage 
room. 

Make sure that there are no bystanders, especially 
children, in the coupling area.

Place the wrapping machine for storage on a hard, 
flat and level ground.

Switch off the tractor engine, remove the ignition 
key and engage the tractor parking brake.

Unplug the electrical power supply.

Disconnect the hydraulic system.

Lower the main chassis support. Disconnect the 
hitch-ring from the transport hitch. Make sure that 
the machine will not move accidentally.

Support the draw bar by using the support stand.

Disconnect the machine draw bar from the tractor 
hitch.

WARNING

It is forbidden to disconnect the wrapping 
machine from the tractor when there is a bale on 
the rotary table.

Clean the machine and inspect its condition 
paying special attention to the quality of the paint 
coat. Touch up paint as required.

Protect the rubber elements, such as hydraulic 
lines, against direct sunlight.

2

Содержание BW200



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды