manualshive.com logo in svg

Farm King BW200, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Farm King BW200 Скачать руководство пользователя страница 25

Operation - 200 Bale Wrapper

23

WARNING

AVOID INJURY OR DEATH

Make sure that there are no bystanders, especially 
children, in the coupling area.

Before coupling the equipment, place the tractor 
axis and the machine axis on a hard, flat, level 
ground. Switch off the tractor engine, remove the 
ignition key and engage the tractor parking brake.

Level the wrapping machine by selecting the 
appropriate adjustment opening in the hitch.

Check whether the machine is properly connected 
and secured against accidental disconnection.

Make sure that the tractor auxiliary hydraulic 
system is without pressure. Move the relevant 
control lever in cabin to eliminate the residual 
pressure in the circuit.

Enter the operator’s position.

Move the tractor into position in front of the 
equipment. Move the tractor backwards, aligning 
the tractor hitch and equipment hitch-ring.

Leave the operator’s position.

Install the hitch pin and retaining pin to securely 
fasten the Backsaver Auger hitch to the tractor 
draw bar. Attach the safety chain around the draw 
bar.

NOTE: Always use a hitch pin of adequate size and 

strength and a retaining pin with a locking 
device.

Plug the electric power source. Check if the 
operating and signaling systems work properly.

Connect the hydraulic power source. Check if the 
hydraulic systems work properly, especially the 
lifting and blocking mechanisms responsible for 
controlling the working and transport positions. 

Load the first bale and make sure that the vertical 
load on the tractor front axle is larger than 20% of 
the tractor weight. The tractor should remain fully 
steerable.

CONNECTING TO TRACTOR

Always inspect the tractor’s hitch and equipment 
hitch-ring before connecting (see the tractor’s 
owner’s manual).

Make sure equipment hitch is resting securely on 
the support stand. Change the hitch to the lower 
or upper position as required.

Figure 5

Remove the M16 bolts (Item 1) and nuts. Flip the 
hitch (Item 2) 180° to upper or lower position. 
Reinstall bolts and nuts 

[Figure 5]

.

Remove the M12 bolts (Item 3), washers, and 
nuts. Flip the hitch-ring (Item 4) 180° to upper or 
lower position. Reinstall bolts and nuts 

[Figure 5]

.

1

2

3

4

LOWER POSITION

UPPER POSITION

Содержание BW200



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды