Farm King 480, Руководство оператора и каталог запасных частей, Страница: 11 / 32

11
Assembly - 480 Grain Cleaner
Side Panel And Trash Pan Option
(See page 16 for drawing)
12. If the cleaner is purchased with a trash pan, the assembly should be done immediately after
the frame assembly (step #3). If the trash pan is added later you will have to assemble it under
the cleaner or pull the cleaner apart. Assembly under the cleaner requires at least two persons.
Bolt the two trash pan ends (#98) and sides (#97) to the bottom trough using 1/4" x 3/4" hex
bolts, lock washers and hex nuts. With the keyed flighting stub shaft facing to the front of
the cleaner, slide the pan assembly into the frame so it rests on the frame sides. The side
panels (#97) have some 5/16" holes along the bottom edge and some 9/16" holes. These holes
should line up with the holes in the trash pan. Bolt on the trash pan at this time using only the
positions corresponding with the 9/16" holes. The remaining 1/4" x 3/4" self tapping screws
mount both the trash pan and the side panels.
Mount a 6" single pulley (#102) at the end of the flighting and a 3" single pulley (#103) at the
end of the reducer shaft (#65). Connect these pulleys with a B-37 belt (#105). Assemble the 3"
idler pulley (#104) on the bracket welded to the front frame using a 5/8" x 3" hex bolt, use a 5/8"
hex nut (#109) if necessary to make sure the idler lines up with the belt. Place 5/8" flat washers
on both sides of the idler and on the slot on the welded bracket.
Bolt the side panels (#97) to the front and rear frame using 1/4" x 3/4" hex bolts, lock washers
and hex nuts and to the frame sides using 1/4" x 3/4" self tapping screws.
8" x 11' Utility Auger Option
(See page 18 for drawing)
13. Bolt the intake assembly (#113) to the bottom of the intake auger (#111) using a clamp (#114)
with 3/8" x 1-3/4" hex bolts, lock washers and hex nuts. Assemble the bottom bearing (#106)
using bearing cup (#115) with 5/16" x 3/4" hex bolts, lock washers and hex nuts. Clamp the flow
control assembly to the tube positioned so the washer welded to the rod acts as a stop when
the intake is completely uncovered by the flow control slide.
The threaded rods on the motor mount assembly (#118) are inserted through the two holes in
the end plate at the top of the auger as shown in drawing. A 3/4" hex nut (#151) on each side
locks the motor mount in place. The threaded rod welded to the top motor mount clamp (#148)
is fitted through the hole in the back of the motor mount. This is also held in place with a 3/4"
hex nut on each side. Bolt the bottom motor mount clamp (#149) to the top half using 3/8" x 2"
hex bolts, lock washers and hex nuts.
Mount the 12" double pulley at the top of the auger. A 2 hp electric motor with a 3-1/2" double
pulley and belt (all supplied by customer) is recommended to drive the intake auger. Tighten
the belt using a 1/2" x 3" sq. head set screw on the motor mount. Mount the guard (#117) using
1/4" x 1" hex bolts, flat washers and hex nuts. One hex nut is placed between the guard and the
brackets bolted to the auger end plate.
Bolt the offset connector (#120) to the auger end plate turned as shown in drawing. This
connector is on the outside of the auger end plate with the offset out towards the pulley. Use
3/8" x 1" hex bolts, lock washers and hex nuts. Bolt the connector plate (#121) to the offset
connector using the same hardware. The swivel (#122) is attached to the connector plate using
pin (#119).
The swivel arm assembly bolts to the frame as shown on page 22. The cradle (#138) bolts to
the back of the frame as shown. A locking pin (#135) locks the arm to the frame. In working
position you turn the arm to the inside and lock in place. During transport, the arm is locked in
the outside position while the intake auger rests in the cradle where it is held down by a clamp
(#139).