Farm King 2400 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 112

Farm King 2400 Скачать руководство пользователя страница 9

Introduction - Round Bale Carrier 2400

9

OWNER’S INFORMATION

Thank you for your decision to purchase a Farm King
2400 Round Bale Carrier. To ensure maximum
performance of your equipment, it is mandatory that you
thoroughly study the Operator And Parts Manual and
follow the recommendations. Proper operation and
maintenance are essential to maximize equipment life
and prevent personal injury.

Operate and maintain this equipment in a safe manner
and in accordance with all applicable local, state, and
federal codes, regulations and / or laws. Follow all on-
product labeling and instructions.

Make sure that all personnel have read this Operator and
Parts Manual and thoroughly understand safe and
correct operating, installation and maintenance
procedures.

Farm King is continually working to improve its products.
Farm King reserves the right to make any improvements
or changes as deemed practical and possible without
incurring any responsibility or obligation to make any
changes or additions to equipment sold previously.

Although great care has been taken to ensure the
accuracy of this publication, Farm King makes no
warranty or guarantee of any kind, written or expressed,
implied or otherwise with regard to the information
contained within this manual. Farm King assumes no
responsibility for any errors that may appear in this
manual and shall not be liable under any circumstances
for incidental, consequential or punitive damages in
connection with, or arising from the use of this manual.

Keep this manual available for frequent reference. All new
operators or owners must review the manual before using
the equipment and annually thereafter. Contact your
Farm King Dealer if you need assistance, information, or
additional copies of the manual. Visit our website at

www.farm-king.com

for a complete list of dealers in

your area.

The directions left, right, front and rear, as mentioned
throughout this manual, are as viewed from the rear of
the equipment.

Serial Number Location

Please enter the model and serial number in the space
provided for easy reference.

Figure 1

The serial number plate (Item 1)

is located on

the inside of the left frame forward of the jack.

Always use your serial number when requesting
information or when ordering parts.

Manual Storage

Figure 2

The Operator And Parts Manual and other documents
can be stored in the canister (Item 1)

located

on the front left side of the carrier.

B-10031

1

Model Number:

Serial Number:

B-10065

1

«
...
7
8
9
10
11
...
»

Содержание 2400

















































































































Отзывы:

Нет отзывов