Farm King 2400 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 112

Farm King 2400 Скачать руководство пользователя страница 44

Operation - Round Bale Carrier 2400

44

End On Bale Pick-Up

Figure 36

Move the tractor and bale carrier straight forward drive so
the inner arm of the loading fork is against the inner edge
of the bale. The bale will then be loaded onto the carrier
in the same direction as it was picked up

[Figure 36]

Press and hold the ARM UP switch to raise the lift arm
placing the bale onto the deck.

NOTE: The momentum of the lift arm makes the bale

roll to the left side, contacting the bale
retainer and then resting between the left
inside and outside carrier beams. When the
second bale is loaded, it will fall into place
between the right inside and outside carrier
beams.

Press and hold the ARM DN switch and fully lower the lift
arm.

Move the tractor and bale carrier straight forward drive so
the inner arm of the loading fork is against the inner edge
of the next bale.

Then load the second bale onto the carrier in the same
direction as it was picked up.

Press and hold the ARM DN switch and fully lower the lift
arm.

Press and hold the PUSHER BACK switch to move
pusher backward, moving the bales far enough to the
rear to provide room to load the next two bales.

Press and hold the PUSHER FWD switch to move
pusher all the way forward.

Repeat procedure until the desired number of bales have
been loaded or the carrier deck is full (Indicator Raised).

Always lower lift arm fully before operating the
pusher.

Always load two bales on the front before operating
the pusher (pushing bales back).

B-10053

«
...
42
43
44
45
46
...
»

Содержание 2400

















































































































Отзывы:

Нет отзывов