Farm King 2400 Скачать руководство пользователя страница 39

Страница: 39 / 112

Operation - Round Bale Carrier 2400

Figure 28

Turn the handle (Item 1)

[Figure 28]

clockwise to raise

the hitch or counterclockwise to lower the hitch.

Lower or raise the Bale Carrier hitch until aligned with the
tractor’s drawbar.

Move to the operator’s seat, start the engine and release
the parking brake.

Move the tractor backwards, aligning the drawbar hitch
pin hole with the Bale Carrier hitch pin hole(s).

Stop the tractor and leave operator’s position.

NOTE: Always use a hitch pin of adequate size and

strength and a retaining pin with a locking
device.

Figure 29

Install the hitch pin (Item 1)

[Figure 29]

and retaining pin

to securely fasten the Bale Carrier hitch to the tractor
drawbar.

Attach the safety chain (Item 2)

[Figure 29]

around the

drawbar.

B-10051

AVOID INJURY OR DEATH

Keep fingers and hands out of pinch points when
connecting and disconnecting equipment.

B-2074

Содержание 2400

















































































































Результаты поиска

Содержание 2400

Отзывы:

Farm King 2400, Руководство оператора и каталог запасных частей, Страница: 39 / 112

Результаты поиска

Содержание 2400

Отзывы: