Farm King 2400 Скачать руководство пользователя страница 38

Страница: 38 / 112

Operation - Round Bale Carrier 2400

Leaving The Operator’s Position

Park the tractor / equipment on a flat level surface.

Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.

INITIAL SET-UP

Connecting The Bale Carrier To The Tractor

Always inspect the tractor’s drawbar and Bale Carrier
hitch before connecting. See the tractor’s owner’s
manual.

Verify that the tractor’s drawbar is adjusted correctly for
use with the Bale Carrier. (See “Drawbar Adjustment” on
page 37.)

Enter the operator’s position. (See “Entering The
Operator’s Position” on page 37.)

Move the tractor into position in front of the Bale Carrier.

Move the tractor backwards, aligning the drawbar with the
Bale Carrier hitch.

NOTE: The jack may need to be lowered or raised for

proper alignment of the drawbar and hitch.

If the Bale Carrier hitch needs to be adjusted, stop the
tractor when drawbar is just in front of the Bale Carrier
hitch.

Leave the operator’s position. (See “Leaving The
Operator’s Position” on page 38.)

AVOID INJURY OR DEATH

Before you leave the operator’s position:
•

Always park on a flat level surface.

•

Place all controls in NEUTRAL.

•

Engage the park brake.

•

Stop the engine and remove the key.

•

Wait for all moving parts to stop.

AVOID INJURY OR DEATH

Before moving the tractor, look in all directions and
make sure no bystanders, especially small children
are in the work area. Do not allow anyone between
the tractor and the equipment when backing up to
the equipment for connecting.

Содержание 2400

















































































































Результаты поиска

Содержание 2400

Отзывы:

Farm King 2400, Руководство оператора и каталог запасных частей, Страница: 38 / 112

Результаты поиска

Содержание 2400

Отзывы: