Farm Fans SCATTERGRAIN FFD-3000VS Скачать руководство пользователя страница 2

Thank you for choosing the Farm Fans FFD-3000VS

Scattergrain. This unit is one of the finest grain
spreaders ever built; designed to give you excellent
operating performance and service for many years.

Operation should not be attempted before reading this

manual; these instructions include information
necessary for successful operation and care of the unit.

USE CAUTION IN THE

OPERATION OF THIS EQUIPMENT

Most accidents, whether they occur in industry, on the

farm, at home, or on the highway, are caused
by the failure of some individual to follow simple and
fundamental safety rules or precautions. For
this reason most accidents can be prevented by recog-
nizing the real cause and doing something about
it before the accident occurs.

Regardless of the care used in the design and con-

struction of any type of equipment, there are many
conditions that cannot be completely safeguarded
against without interfering with reasonable acces-sibility
and efficient operation.

A CAREFUL OPERATOR IS THE BEST INSURANCE
AGAINST AN ACCIDENT.

THE COMPLETE OBSERVANCE OF ONE SIMPLE
RULE WOULD PREVENT MANY THOUSAND SERI-
OUS INJURIES EACH YEAR.  THAT RULE IS: STOP
MACHINE TO ADJUST, LUBRCIATE, SERVICE,
CLEAN OR MOVE.

O

O

PERATING PRECAUTIONS

Look for this symbol to point out important
safety precautions. It means ATTENTION!
BECOME ALERT! YOUR SAFETY IS
INVOLVED.

1. Read and understand the operation manual before
attempting to operate the unit.

2. Stop unit before attempting to adjust, service, clean
or move.

3. Keep visitors, children and untrained personnel away
from unit at all times.

4. Always open the main power supply disconnect
switch and lock it in the open position using a padlock
before performing any service or maintenance work. It is
highly recommended that each worker have his own
lock and key.

WARRANTY

Farm Fans, a divisionof ffi Corporation, warrants its
products to be free of defects in material and workman-
ship. The only obligation of the manufacturer is to repair
or replace products which have been submitted and
found to be defective within 12 months after installation.
If so found defective, the products will be repaired or
replaced without charge, this constituting and entirely
fulfilling the warranty obligation.  Farm Fans assumes
no liability for expenses incurred without written autho-
rization; in no event shall its liability include special or
consequential damages, or exceed the selling price
of the product.

This warranty does not cover products or parts which
have been damaged by negligent use, misuse, alter-
ation or accident. Electric motors, tires, and other com-
ponents supplied by manufacturers are warranted sepa-
rately by those suppliers. This warranty is exclusive and
in lieu of all other wat-ranties, expressed or implied.
Farm Fans reserves the right to make design or specifi-
cation changes at any time, without any contingent
obligation to purchasers of products already sold. All
instructions shall be construed as recommendations
only; because of the many variable conditions in actual
installation, Farm Fans assumes no liability for results
arising from the use of such recommendations.

Copyright © 1997 by Farm Fans, a division of ffi Corporation.  All rights reserved.  No part of this publication may be used or reproduced in any form
or by any means without prior permission.  Failure to comply with this notice is a violation of United States copyright laws.

Содержание SCATTERGRAIN FFD-3000VS













Отзывы: