Fargo DTC4500 Скачать руководство пользователя страница 52

Страница: 52 / 140

2011

HID

Global

Corporation

All

rights

reserved

DTC4500

Card Printer/Encoder User Guide L001444 Rev1.1

Selecting the Advanced Settings tab

Setting

Option

Write Heat Offset

Adjust the Write temperature for the rewriteable cards as
needed.

•

Increase

the

Current Setting

to cause more heat to

be used in the printing process of a rewritable card.

•

Decrease

the

Current Setting

to cause less heat to be

used in the printing process of a rewritable card.

(Note: Write Heat Offset

provides user ability to control

the Printhead heat level when the Write Operation is
performed. Appropriate heat levels should be applied for
the proper writing process.)

Enable Swift ID over USB
connection

Enable Swift ID over a USB connection -

Check this

item to utilize Swift ID via a USB connection. When this
box is checked the Ethernet connection (if applicable) on
the printer will not be operational.

•

If the USB selection is not be accessible, the HID EEM

driver that Swift ID uses to connect via a USB
connection has not been installed.

•

This driver can be found on the installation CD or it can

be down loaded from the HID Global support page.

•

The easiest method for enabling Swift ID is to un-

install the printer driver and its components and go
through the installation procedure.

Select the desired connection type for the Swift ID
application: USB or ETHERNET.

Содержание DTC4500






























































































































Результаты поиска

Содержание DTC4500

Отзывы:

Бренды по названию

Популярные бренды

Fargo DTC4500, Руководство пользователя

Результаты поиска

Содержание DTC4500

Отзывы:

Бренды по названию

Популярные бренды