FARGO electronics Quatro Quatro ID Card Printer Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 56

background image

8 Ribbons and Cards

3.

Open the Top Cover of the printer by gently grasping the
front sides of the cover and lifting upward. The cover will
tilt open from front-to-back.

4.

Open the Printhead Assembly by gently pulling up on the
assemblyÕs Release Tab and lifting upward. Allow the
assembly to swing completely open.

5.

Place the supply end of the ribbon in between the two
black Ribbon Drive Hubs located on the right-hand side of
the printerÕs interior. Make certain that the ribbon is fed
from

underneath

the ribbon roll.

HINT: The Ribbon Drive

Hub nearest you, as you are looking into the printer from
the front, is spring loaded. Use the end of the ribbon
supply core to push in this Ribbon Drive Hub when
inserting the ribbon.

Release Tab

Printhead
Assembly

Quatro/510323 v3 1/8/99 10:48 AM Page 8

«
...
10
11
12
13
14
...
»

Содержание Quatro Quatro ID Card Printer

























































Отзывы:

Нет отзывов

Похожие инструкции для Quatro Quatro ID Card Printer

Бренд: LabelTac Страницы: 2

Бренд: D-Link Страницы: 12

Бренд: Pandigital Страницы: 2

Бренд: EasyThreed Страницы: 4

Бренд: EASYPRINT Страницы: 37

Бренд: idp Страницы: 88

Бренд: TallyGenicom Страницы: 92

Accel-a-Writer 8300

Бренд: Xante Страницы: 12

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 16

Pixma TS7700i Series

Бренд: Canon Страницы: 554

Бренд: Grizzly Страницы: 56

Бренд: Xerox Страницы: 418

Бренд: Duplo Страницы: 123

Imagistics 2500

Бренд: Axis Страницы: 16

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 4

Бренд: AstroJet Страницы: 32

Бренд: SPRT Страницы: 48

Бренд: Konica Minolta Страницы: 424

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды