Fanvil A2 Скачать руководство пользователя страница 12

Страница: 12 / 48

button again, you can switch back. You also can send and receive on one side, then

the party can not be retained to hear your conversation, the speaker you can not.

(To use this feature, you must enable the gateway of the Call Waiting feature)

5. Web configuration

5.1. Introduction of configuration

5.1.1. Ways to configure

A2 two-port gateway has two different ways to different users.

Use web browser

（

recommendatory way

）

Use telnet with CLI command.

5.1.2. Password Configuration

There are two levels to access to gateway: root level and general level. User with

root level can browse and set all configuration parameters, while user with general

level can set all configuration parameters except SIP (1-2) that some parameters

can not be changed, such as server address and port. User will has different access

level with different username and password.

Default user with general level

：

username

：

guest

password

：

guest

Default user with root level

：

username

：

admin

password

：

admin

5.2. Setting via web browser

When this gateway and PC are connected to network, enter the WAN port IP

address of the gateway as the URL (e.g. http://xxx.xxx.xxx.xxx/ or

http://xxx.xxx.xxx.xxx:xxxx/).

Gateway IP address can be received by dialing # * 111.

The login page is shown as below

Содержание A2

















































Результаты поиска

Содержание A2

Отзывы:

Fanvil A2, Руководство пользователя, Страница: 12 / 48

Результаты поиска

Содержание A2

Отзывы: