background image

1

5

PREPARATIONS BEFORE USE 

WINDING THE POWER CORD

Hook the  power cord over the clip 

which is located on the upper  

cord storage hook as shown.

2

Wind the power cord around 

the cord storage hooks.

INSERTING THE POWER CORD PLUG

Plug Side

Clip

Secure  the  power

cord plug on the 

power cord. 

Cord  Storage

Hooks

THERMAL SAFETY DEVICE IN MAIN BODY

To protect your vacuum cleaner motor from overheating, a thermal safety device has been 

built in. If your vacuum cleaner hose or air intake clogs up with dust or dirt, or if your dust 

bag becomes full and you continue to run the machine, the vacuum will shut off 

automatically to prevent the motor from overheating. If this happens, turn off slide  switch 

and disconnect your vacuum from power outlet, remove the material clogging the machine 

and let your vacuum cool down for approximately 20 minutes. You can then restart your 

vacuum cleaner and use it again.

WARNING:  This appliance is equipped with a 

grounded-type 3-wire cord (3-prong plug). This plug 

will only fit into an electrical outlet made for a 3-prong 

plug.  This is a safety feature.  If the plug should fail to 

fit the outlet, contact an electrician to replace the outlet. 

Do not attempt to defeat the safety purpose of the 

grounding pin, part of the 3-prong plug. 

Содержание FM655CS




















Отзывы: