Fantasea FFL 50 страница 11 Скачать руководство пользователя

Страница: 11 / 17

MOUNTING THE SPEEDLIGHT IN THE HOUSING

INSERTING

Since the

Fantasea FFL 50 Flash Housing

was specifically designed for the Olympus FL50 Speedlight,

insertion is a simple matter of placing the flash into the housing. Make sure the flash is properly aligned and

that it sits perfectly flat. There are no screws or mounts to worry about or any other alignments once the

flash is properly inserted.

Set the flashlight in an upright position. Slide the flashlight all the way into the hot shoe of the housing until

it stops

Notes:

It is recommended first to attach the flash to the camera's

hot shoe to determine if it is functioning properly.

Once this is determined, insert both into their respective

housings.

Turn the lock ring follow the direction “LOCK”. Take care not to excessively tighten the screw. Note: If

you find that control levers do not locate properly with the buttons, please check again that the flashlight is

properly seated to the limit of the guide rail.

IGURE

LIDE IN AND

OCK THE

LASHLIGHT

Содержание FFL 50


















Результаты поиска

Содержание FFL 50

Отзывы:

Похожие инструкции для FFL 50

Бренды по названию

Популярные бренды

Fantasea FFL 50, Руководство пользователя

Результаты поиска

Содержание FFL 50

Отзывы:

Похожие инструкции для FFL 50

Бренды по названию

Популярные бренды