Fanimation Windpointe MW75 Series Скачать руководство пользователя страница 4

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle 
of the room and at least 2.1 m above the floor and 50 cm 

 

 from the walls. If ceiling height allows, install the fan 

2.4-2.7 m above the floor for optimal airflow. 

 

4

This new ceiling fan will require a grounded electrical supply 
line  of  220-240  volts AC,  50  Hz  circuit.  The  hanger
bracket must be securely anchored and capable of 
supporting a load of least 27kg. If your fan is to replace an
existing ceiling light fixture, turn electricity off at the main
fuse box at this time and remove the existing light fixture.
Figure 1 depicts a typical structural configuration that may
be used for securely mounting the fan.

WARNING

Turning  off  wall  switch  is  not  sufficient.    To  avoid 

possible  electrical  shock,  be  sure  electricity  is  turned 

off at the main fuse box before wiring.  All wiring must 

be in accordance with AS/NZS 3000 “The Wiring Rules” 

and the ceiling fan must be properly grounded as a  

precaution against possible electrical shock.

WARNING

This fan must be installed by a licensed electrician. 

Electrical and Structural Re uirements

s

n

a

F

 

g

n

il

i

e

C

 f

o

 

e

s

U

 t

n

e

i

c

 if

f

E

 

y

g

r

e

n

E

Ceiling  fan  performance  and  energy  savings  rely 
heavily on the proper installation and use of the ceiling 
fan.    Here  are  a  few  tips  to  ensure  efficient  product 
performance.

Turn Off When Not in the Room

Ceiling  fans  cool  people,  not  rooms.  If  the  room  is 
unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round
Summer  Season:

  Use  the  ceiling  fan  in  the  counter-

clockwise  direction.   The  airflow  produced  by  the  ceiling 
fan  creates  a  wind-chill  effect,  making  you  “feel”  cooler. 
Select  a  fan  speed  that  provides  a  comfortable  breeze, 
lower speeds consume less energy.

Winter Season:

 Reverse the motor and operate the ceiling 

fan at low speed in the clockwise direction. This produces 

 

a gentle updraft, which forces warm air near the ceiling 

 

down into the occupied space. Remember to adjust your  

 

air conditioner when using your ceiling fan-additional energy 
and dollar savings could be realized with this simple step!

Ceiling

Ceiling

Joists

Ceiling

Joists

Figure 1

50 X 100 mm
Timber Batten
Between Joists

Содержание Windpointe MW75 Series















Отзывы: