- 6 -
Controller reset
Keep the UP button pressed for a controller to reset itself and dis
-
connect heating device.
Press the ON/OFF button to return to operation.
Protection
To protect the controller from unauthorized access, press the
UP/DOWN button for a longer time.
Activation of the protection is signaled by a padlock symbol on the
display. Unlocking is done in the same way.
Automatic/manual operation
Longer press of the DOWN button changes the controller mode of
operation from automatic to manual and vice versa (day time icon
goes off).
Manual operation - room temperature control is based on the cur
-
rent setting. Use the UP/DOWN buttons to change the temperature.
Automatic operation - the temperature is maintained on the basis of
the pre-programmed cycles of the controller.
Temperature readout
If the controller is set to operate with two temperature sensors by
short press of the ON/OFF button, the readout source changes from
the internal sensor to the external.
Controller operation errors indication
Er1 - damage to internal temperature probe
Er2 - damage of external temperature probe
Er3 - damage to internal and external probe
- 8 -
D161220
Technical data
power supply
230 V AC
current load heating circuit
<16 A
temperature adjustment range
5÷55°C
histeresis
2°C
setting accuracy
1°C
measurement accuracy
±0,1°C
power consumption
1 W
working temperature
0÷65°C
terminal
2.5mm² screw terminals
dimensions
front
86×86 mm; D= 22 mm
back
6
27.5 mm
mounting
external temperature sensor
NTC
sensor dimensions
Ø7
Ø 0; D=
in
flush mounted
ingress protection
IP20
Ø60
; h=25 mm
sensor isolation
PC muff
wire
PC 2×0,34 mm²; l= 3 m
3.
Remove the cover and the frame of the controller, taking care not
to damage the electronics of the controller.
4. Connect according to the scheme.
5. Place the bottom part of the controller in the flush-mounted box
and fix it with the screws.
6. Put the frame back on and press the cover.
- 7 -
Mounting
1.
Disconnect the power supply from the cir
-
cuit to which the controller will be con
-
nected.
2. Using a narrow, flat-blade driver, gently
press the catch (marked with the arrow on
the drawing) to lock the controller
housing.
Connection scheme
probe
N
L
1
2
3
4
5
6
OUT
N
heater
1/4 -
output for heater connection
2
-
L power supply of the controller
3
- N
power supply of the controller
5/6 -
output for temperature probe connection
Take special care when installing the controller. Incorrect
connection may result in electric shock and/or damage to
the controller and the powered device.
Do not install a device that is damaged or incomplete.
Do not install the device in rooms with high humidity, such
as bathrooms.
Setting up a weekly operation program:
1. Press the MENU button to enter the programming mode.
2. Use the UP/DOWN buttons to select parameter F8 and confirm
with the ON/OFF button.
3. Use the UP/DOWN button to select the day of the week: MON-
FRI, Saturday or Sunday (SAT, SUN).
Example: Select MON-FRI and confirm with the ON / OFF button.
4. Use the UP / DOWN buttons to select the time of day.
Example: Select in the morning, confirm with the ON/OFF button.
5. Use the UP/DOWN buttons to set the start time of the "morning"
time of day.
Example: Select 06:00 (change with increments of 15 minutes),
confirm with ON/OFF button.
WARNING! The start time of the next period is the end of the
previous one, so there is no option to set the ending time of the
given period).
6. Use the UP/DOWN buttons to set the desired temperature for
this time of day - morning. The temperature can be changed
every 1 °C in the range of 5÷55 °C. Confirm with the ON/OFF
button.
7. Once the temperature value has been confirmed, the program
automatically returns to step 4, allowing to set the parameters of
the next time of day.
8. After setting the start times and temperature values, the
program will automatically switch to setting the time for
Saturday, and then for Sunday. After entering the last parameter
for Sunday and confirming it with the ON/OFF button, the
program will return to the selection of parameters F1÷F8.
9. To exit the programming mode press the MENU button or wait 5
seconds and then the controller automatically returns to normal
operation.
- 5 -
