background image

- 1 -

DR-30M

Motion sensor (PIR),

detection range 30 m

The DR-30M sensor is used for automatic, temporary switching 

of lighting when a moving person or other object is detected. It is 

especially recommended for use in high rooms and storage halls 

up to 12÷15 meters high.

The sensor detects sources of infrared radiation and analyzing 

parameters such as the amount of heat emitted and the speed at 

which the object moves determines the switching of the lighting. 

Infrared sensors have the highest performance when detecting 

motion perpendicular to the sensor axis and the lowest when 

motion is directly in the direction of the sensor. Only if there is 

no movement in the detection area triggers the lighting support 

time. Another movement in the detection area and its subsequ-

ent disappearance in the course of time measurement starts the 

support time from the beginning.

Purpose

Functioning

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: [email protected]

Do not dispose of this device in the trash along with other waste! 

According to the Law on Waste, electro coming from households free of charge and can 

give any amount to up to that end point of collec� on, as well as to store the occasion of 

the purchase of new equipment (in accordance with the principle of old-for-new, regard-

less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the 

environment and human health.

Содержание DR-30M
















Отзывы: