20
MAINTENANCE
Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching of the
main switch.
Regular maintenance guarantees proper operation and good performance over time.
Special attention is to be paid to the metal anti-grease ilters and active carbon ilters. In fact, frequent cleaning of the ilters and their supports
ensures that no grease is accumulated on the hood, which is dangerous and can cause ires.
EXTERNAL CLEANING
You are advised to clean the external surfaces of the hood
at least once every 15 days
to prevent oily substances and grease from sticking to them.
To clean the brushed stainless steel hood, the Manufacturer recommends using "Magic Steel" wipes. Alternatively, it can be cleaned using a damp
cloth, slightly moistened with neutral, liquid detergent or denatured alcohol. Finish of cleaning by rinsing well and drying with soft cloths.
Do not use too much water next to the push button control panel and lighting devices in order to prevent humidity from reach-
ing electronic parts. You must not use detergents containing abrasive, acid or corrosive substances or abrasive cloths: a direct
consequence of not complying with these warnings will result in irreversible deterioration of the hood's surface.
The glass panels can only be cleaned with speciic, non-corrosive or non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these instructions.
It is possible to remove the external suction panel completely in order to facilitate its cleaning (refer to the instructions
).
CLEANING OF INTERNAL PARTS
It is forbidden to clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.
Do not use abrasive products.
All these operations are to be carried out after having disconnected the equipment from the electrical mains power supply.
METAL ANTI-GREASE FILTERS
The metal anti-grease ilters are there to contain suspended grease particles: deposited on the ilters, these feed on any
lames released when cooking, generate unpleasant odours, and compromise the passage of air, thus reducing suction
performance of the hood.
For this reason, it is advised to
frequently
wash the metal ilters (
at least
once a month)
leaving them to soak in boiling
water and dish washing liquid for 1 hour, taking care not to bend them. Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the ilter material to darken: to reduce the possibility of this
problem from happening, use low-temperature washes (55°C max.).
Open the external suction panel to remove the metal anti-grease ilters (refer to the instructions
), then operate the handle
(refer to the instructions
). Carry out operations in reverse order to insert them.
ACTIVE CARBON FILTERS
Active carbon ilters have the function of retaining odours in the air low passing through them. The air, puriied by running
many times through the ilter, is recirculated into the kitchen.
Active carbon ilters
cannot be washed
and are to be immediately replaced every
3-4 months
(depending on the fre-
quency of use of the hood).
Dispose of the active carbon ilters in compliance with the regulations in force in the country of use.
To replace the active carbon ilters, open the external suction panel (refer to the instructions
remove the metal anti-grease ilters (refer to the instructions
page
.
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out wheeled bin symbol on the appliance means that
the product is WEEE
, i.e.
"
waste electrical and electronic equipment", according-
ly
it must not be thrown out with unsorted waste
(i.e. with "mixed household waste"), but it must be disposed of separately so that it can undergo
speciic operations for its re-use, or a speciic treatment, to remove and safely dispose of any substances that may be harmful to the environment
and remove the raw materials that can be recycled. Correct disposal of this product contributes to saving precious resources and avoiding potential
negative efects on human health and the environment, which could be caused by inappropriate waste disposal. You are kindly asked to contact
your local authorities for further information regarding the designated waste collection points nearest to you. Penalties for improper disposal of such
waste can be applied in compliance with national regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented diferently in each country, accordingly, if you wish to dispose of this appliance we suggest contacting
your local authorities or dealer to ind out what the correct method of disposal is.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed-out wheeled bin symbol is only valid in the European Union: if you wish to dispose of this appliance in other countries, we suggest
contacting your local authorities or dealer to ind out what the correct method of disposal is.
Содержание blade 90
