8.0 Labels
The labels must be present and legible.
MANC33 Rev B
020320
11
REV
TITLE
ITEM NO.
SIZE
SHEET
SCALE
412-05069
Label, Post Anchor, Various Info,
Warning, Inspection Grid
REVISIONS
REV
DRAWN
DATE
P1 PRELIMINARY INITIAL RELEASE
DESCRIPTION
10-3-19
Sam
A PRELIMINARY INITIAL RELEASE
10-14-19
Sam
THE INFORMATION EMBODIED IN THIS DOCUMENT IS STRICTLY
CONFIDENTIAL AND ARE SUPPLIED WITH THE UNDERSTANDING
THAT THEY WILL NOT BE DISCLOSED TO THIRD PARTIES
1:1
1/1
A
A
GENERAL NOTES:
1.
2.
3.
4.
WEIGHT (FOR REFERENCE ONLY)
N/A
N/A
ZW
Samuel Andrade
N/A
N/A
N/A
Polycarbonate coated vinyl
APPLICABLE STANDARDS:
ASME Y14.5-2009 & DIN ISO 2768
EXCEPTION: TRAILING ZEROS DENOTE
TOLERANCE
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN MILLIMETERS (mm)
TOLERANCES ARE:
0 to 6 ...........................................
6 to 30 .........................................
30 to 120 .....................................
120 + ...........................................
ANGLES .....................................
APPROVED
MFG
CHECKED
SURFACE ROUGHNESS
SURFACE FINISH
10-3-19
MATERIAL
DRAWN
10-14-19
N/A
N/A
0.1
0.2
0.3
0.5
0.5
PANTONE black C
PANTONE 152C
PANTONE 5415C
152mm
76mm
40mm
DIE CUT LINES
DO NOT REMOVE
LABEL
All Manufacturer’s instructions, labels, and warnings must be read
before use and followed at all times for proper use, maintenance,
and inspection. Users must be fully trained and knowledgeable
about all government and regulatory requirements applicable to
workplace safety. This equipment must be installed and used under
the supervision of a qualified person. Failure to follow instructions
or misuse of this product may result in serious injury or death.
Exercise caution using this equipment near hazardous thermal,
electrical, or chemical sources. Avoid contact with sharp edges,
abrasive surfaces, chemicals, salt water, acids, and alkalines. See
instructions for loading direction diagram and restrictions on use
with components, subsystems, or systems with which this product
is designed to be used. Inspect the system before each use,
following guidelines found in the user instruction manual supplied
with product at time of shipment. Do not use system if unsafe
conditions are present. Remove from service if equipment is
subjected to fall arrest forces. Always log inspection results in
user manual and on inspection grid label.
412-05069 Rev A
Model#:
Date of Mfr:
Serial #:
MARK ON DATE GRID A) INITIAL SERVICE DATE
B) DATE OF PASSED INSPECTION . IF UNIT FAILS INSPECTION
REMOVE IT FROM SERVICE
YEAR
Material: Steel
Meets: ANSI Z359.18-2017 Type D for Steel and Concrete
Meets: OSHA 1926.502 for Wood, Steel, and Concrete
Minimun Service Temperature: +10 F
Minimum Breaking Strength (MBS): 5,000 lbs.
800-719-4619 falltech.com
DO NOT REMOVE
LABEL
All Manufacturer’s instructions, labels, and warnings must be read
before use and followed at all times for proper use, maintenance,
and inspection. Users must be fully trained and knowledgeable
about all government and regulatory requirements applicable to
workplace safety. This equipment must be installed and used under
the supervision of a qualified person. Failure to follow instructions
or misuse of this product may result in serious injury or death.
Exercise caution using this equipment near hazardous thermal,
electrical, or chemical sources. Avoid contact with sharp edges,
abrasive surfaces, chemicals, salt water, acids, and alkalines. See
instructions for loading direction diagram and restrictions on use
with components, subsystems, or systems with which this product
is designed to be used. Inspect the system before each use,
following guidelines found in the user instruction manual supplied
with product at time of shipment. Do not use system if unsafe
conditions are present. Remove from service if equipment is
subjected to fall arrest forces. Always log inspection results in
user manual and on inspection grid label.
412-05069 Rev A
Model#:
Date of Mfr:
Serial #:
MARK ON DATE GRID A) INITIAL SERVICE DATE
B) DATE OF PASSED INSPECTION . IF UNIT FAILS INSPECTION
REMOVE IT FROM SERVICE
YEAR
Material: Steel
Meets: ANSI Z359.18-2017 Type D for Steel and Concrete
Meets: OSHA 1926.502 for Wood, Steel, and Concrete
Minimun Service Temperature: +10 F
Minimum Breaking Strength (MBS): 5,000 lbs.
800-719-4619 falltech.com
10mm
CUT OUT
