Falcon i9042 Скачать руководство пользователя страница 30

Страница: 30 / 37

Cooking Zone
Temperature Too
High Or Remains
Constant During
Cooking.

Reset Appliance

Switch Appliance OFF for
10 Seconds then On.

Pan empty / Too Hot

Test Disc may be
overheated – allow for
cooling.

Cooking Zone Self
Protected due to Abnormal
Heat Build up

Allow Cook Zone to cool
for couple of Minutes

Temperature sensor faulty
(Constantly records a
Ambient Temperature)

Check all electrical
connections to the
inductor coil

Replace defective Coil

Controls Failure

Reset Appliance

Switch Appliance OFF for
10 Seconds then On.

Controls faulty or
incorrectly Wired

Check all electrical
connections to the
controls & Generator

Replace defective
Controls Assembly

Generators
Internal
Temperature Too
High.

Reset Appliance

Switch Appliance OFF for
10 Seconds then On.

See Fault 3

Cooking Zone
Temperature
Sensor

Reset Appliance

Switch Appliance OFF for
10 Seconds then On.

Temperature sensor faulty /
Malfunctioned

Check all electrical
connections to the
inductor coil

Replace defective Coil

Mains Supply
Failure

Reset Appliance

Switch Appliance OFF for
10 Seconds then On.

Fault in mains supply

Is there a Phase(s) Down

Has supply been
interrupted intermittently?

Has MCB Tripped

Has Supply Under / Over
Voltage?

Содержание i9042






































Результаты поиска

Содержание i9042

Отзывы:

Falcon i9042, Инструкция для пользователя, по установке и обслуживанию, Страница: 30 / 37

Результаты поиска

Содержание i9042

Отзывы: