background image

14

Calibrating the Balance Point

When riding for the fi rst time or after an extended period, it is a good idea to calibrate the 

system to fi nd a balance point. While in the off  state, press the power button and the mode 

button together for two seconds. After a few “beeps,” the vehicle will calibrate its systems. 

At this point, the vehicle shoud level the platform and a fi nal “beep” will confi rm that the 

calibration is complete. After calibrating, the system will automatically shut down. 

Correcting the platform level and directional data

While in standby mode, press the power button and mode display button until you hear 

a “beep.” The display lights shouldturn on - from here you can confi gure 5 diff erent pa-

rameters represented on the battery indicator. The fi rst light adjusts the controls for the 

left platform step, the second light controls the right platform. The third and fourth light 

adjusts the abatement for both left and right platforms. The fi fth light adjusts the sensi-

tivity of the steering. To increase the values for each, press the display button to gradually 

increase the desired parameter. Upon each button press, the light increases in brightness 

incrementally.

Set the running time

Press the power button and lock button until you hear a “beep” to enter the setup. The dig-

ital display should read 0. Press the mode key to reduce the number, the power button to 

cancel the setting and revert to default, the lock key to save and exit, and the display key 

to increase the value. 

Digital tube numerical switch 

While in standby mode, press the display key to switch the display value - this will display 

the value in running time - press it again to cycle display of speed and mileage. To set the 

default of which to display on the panel, press the mode key and display key at the same 

time while the display is on the desired parameter (running time, speed, or mileage) until 

you hear a beep. Press the mode and display key again to save this setting.

Change between high and low speed

By default, the Falcon is set to high speed (20km/h) - press the mode key upon seeing the 

frequency display on the panel- the status lights should display a new frequency  that rep-

resents low speed mode (10km/h).

Содержание Daymak















Отзывы: