background image

13

5.

  Select the smallest rear sprocket, if there is any evidence of chain rub adjust the outer screw 

until this just ceases. The lower edge of the outside plate should be positioned approximately 

1-3 mm above the largest outside chainring. If a biopace chain set is fitted as indicated on the 

chainring the clearance should be measured above the highest point of the ring.

6

.  If a chainwheel disk is fitted, make sure there is sufficient clearance between changer cage 

and chainwheel disk.

7

.  If problems continue to arise, the bicycle should be checked by a professional repairer.

1-3mm

Inside front changer

Chainwheel disk

Adjusting screws

Operating wire

from left hand

gear control

Outside front changer

Outside Chainwheel

Middle Chainwheel

Inner Chainwheel

VIEW FROM SIDE

Outer adjusting screw 

sets outer movement limit

Chainwheel disk

Front changer cage

Inner adjusting screw 

sets inner movement 

limit

Using the adjusting screws set the limit for the 

movement of the front changer cage

VIEW FROM ABOVE

STI RAPIDFIRE

STI Rapidfire lever uses two push levers mounted conveniently under the bar in front of the 

thumb. Using lever (A) you can shift one gear at a time, or shift down the entire block with a full 

stroke push. Using lever (B) you can shift up the sprocket with the same capability.

STI OPERATION
Rear Gear Operation
Right Hand Lever.

Lever  (A)  — 

operated 

by  your  right  hand 

thumb  pressing  away 

from your body (shifting 

from a small sprocket to 

a larger sprocket)

 

2) To shift two gears at a time 

from a small sprocket to a larger 

sprocket press Iever A twice

Example: from 2nd to 4th

3)  To  shift  three  gears  at  a 

time from a small sprocket to 

a larger sprocket press lever 

A three times

Example: from 2nd to 5th

Lever (B)

 - operated by pulling with your your right hand forefinger or pushing with 

your thumb depending on model of shifter. (shifting from a large sprocket to a small sprocket)

When lever (B) is pulled once, 

there is a one-step shift from a 

larger gear to a smaller gear

Example: from 3rd to 2nd

1

2

3

Click

Click

Click

Right hand lever viewed from below

Right hand lever viewed from below

1) To shift one gear at a time 

from  a  small  sprocket  press 

lever A once

Example: from 2nd to 3rd

3 2

4  2

5    2

3 2

Rear gear changer. Right hand lever

Lever B

Lever A

Содержание CYCLES





















Отзывы: