not pull down; merely wrap the tubes at this location with 6” Velcro strips; one on each side of the roll
cage. Wrap the double-sided Velcro strips around the hook strips to attach the center of the top of the
enclosure. See diagram in fig.1.
5.
Install the Polycarbonate windshield. See separate instructions for windshield assembly, however do not
attach the upper brace to the windshield until windshield has been fitted to vehicle. Ensure that the top
of the windshield slides underneath the front visor at the top of the enclosure. Slide the clamps around
the tubes as illustrated in the Polycarbonate windshield installation instructions. The clamps will fit
around the tubes at the gaps between the Velcro tabs on the enclosure. Follow the rest of the
Polycarbonate windshield installation instructions as written, however do not yet install the upper brace.
Ensure that the binding underneath the visor at both sides lines up with the vertical edges of the
Polycarbonate windshield on both sides; some position adjustment of the front enclosure strips may be
necessary. Locate the holes for the upper brace in the windshield; holes in the front visor will need to be
made with a small blade to fit the upper brace over the outside of the visor. The visor should be
sandwiched between the brace and the windshield. See diagram in fig.2.
6.
Once the main enclosure and windshield have been fitted to the vehicle, move to the rear and attach the
rear window to the enclosure at the zipper across the top, on the outside of the divider screen. Mark the
location where the bottom of the rear window meets the divider screen and apply the 43” adhesive hook
strip provided across the divider screen. Attach the Velcro sewn in across the bottom of the rear window
to the adhesive hook strip across the bottom of the divider screen. Now wrap the roll cage tubes below
the air intake vents with a 6” adhesive hook strip on both sides of the frame. Attach the double-sided
Velcro straps at the bottom of the enclosure to the hook strips wrapped around both sides of the bottom
of the frame.
7.
Now zip the side doors onto the enclosure one at a time starting with the front/top main zipper. Next zip
down the side of the rear window. There are three double-sided Velcro straps on the inside of the doors
that attach to the frame; mark their positions on the frame and wrap the tubes with a 6” adhesive hook
strip at each location. Attach the double-sided Velcro strips on the enclosure to the hook strips on the
frame. The only remaining adhesive Velcro strips should be the two 8”x1” pieces provided. At the rear
of the door panels there are two 8” Velcro tabs sewn into the door panels. Apply adhesive hook strips to
the bed of the vehicle at these locations, running vertically. Attach the Velcro tabs on the enclosure to
the adhesive hook strips on the bed. See figs. 1 and 3.
8.
Mark the locations for the stud snaps on the front fenders, 4 per side. Install using a #2 Phillips
screwdriver and do not overtighten. Attach snaps on enclosure to snap studs on front fender. See fig. 3.
Cleaning and Storage Recommendations:
1.
Before removing the cab for storage, make sure it is clean and dry, to prevent soiling the textile and
scratching the clear vinyl side/rear windows. Clean with a soft rag or sponge using a mild liquid
detergent soap and warm water solution. Let the cab dry thoroughly before attempting to roll for storage.
2.
It is important that the cab be rolled up for storage rather than folding. Folding will cause undesirable
creasing of both the cab textile and the clear vinyl side/rear windows. Carefully roll up the cab similar to
the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over
the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the cab into
a roll approximately 8” in diameter. Put the rolled cab back into the carton for storage at a normal room
temperature. It is best not to expose the cab to either extreme hot or cold temperatures when storing.
3.
A special cleaner/conditioner is available from Falcon Ridge that will greatly increase the service life of
the cab enclosure. If needed, additional hook and loop sets are available, as well as other spare parts and
hardware. Contact Falcon Ridge for information.
Содержание KAW-3010TRANS-FC03
Страница 4: ...Fig 2 ...
Страница 5: ...Fig 3 ...
