background image

If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level
of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to 

www.z-wave.info

.

Product Description

The ZWS230 chain motor is thanks to its small dimensions and suitable force output ideal for roof window
operating and is fully compatible with the Z-Wave system. The motor can be used to upgrade centre pivot
and top hung and pivot roof windows of different manufacturers.

The maximum chain reach of the ZW230 is 36cm. The motor is equipped with built-in overload protection which acts as a sensor for correct window closing.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do
this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended
to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the
assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

The Chain Drive for Pivot Windows (230V) is intended for operating centre pivot and top hung and pivot roof windows. The ZWS motors are equipped with a
twoway "Z-Wave" communication radio module. ZWS motors are Security Enabled products. Security Enabled Z-Wave Controller must be used in order to fully
utilize ZWS. The motor functionality is anyway identical when included as a secure and non-secure device.

The ZWS motors are equipped with two limits:

limit switch at maximum chain travel position

overload limit at folded chain position

Install the ZWS motor with your roof window according installation manual.

 

 
Please read carefully the instructions below before proceeding to the device installation so as to prevent electric shock or injury. When installing the mechanical

Содержание ZWS230









Отзывы: