Fairport F14-35 Скачать руководство пользователя страница 13

 

12 

 

9.  Warranty Conditions and Claims Procedure

 

All products supplied by Fairport Construction Equipment Ltd (hereafter referred to as FCE) 

are warranted to be free of defects due to faulty materials or workmanship for a period of 12 

months from the date of original despatch from FCE or as specified below: 

Hydraulic hoses and hydraulic couplings – 3 months.  

Hydraulic accumulators – 6 months. 

Fexible drives – 6 months. 

All spare parts used in repairs carried out by FCE or an authorised dealer or repairer 

– 3 months. 

If the goods have been purchased through a stockist the above warranty periods also apply 

from receipt of the goods by the user of the equipment up to a total of a further 6 months 

from date of despatch from FCE whichever is earlier. 

Filter elements, gauges and oils are specifically excluded from this warranty. 

FCE shall at their option repair or replace during normal working hours goods accepted as 

faulty free of charge to the user.  

For proprietary items such as engines, the original manufacturer’s warranty and conditions 

shall apply. 

 

CONDITIONS 

The goods shall be returned at the purchaser’s expense to FCE or to a destination FCE may 

reasonably direct.  Carriage costs will be refunded if warranty is accepted. 

Warranty claims will not be considered where there is evidence that failure has been caused 

by carelessness, improper use, negligence, inadequate servicing, incorrect engine speeds, 

fair wear and tear or non-compliance with instructions issued by the manufacturer. 

To the extent permitted by law, the liability of FCE under this section is confined only to 

providing a remedy for defective goods and does not extend to any consequential loss, loss 

of profit, injury or damage suffered. 

Warranty will not be accepted on dismantled goods unless dismantling was carried out with 

the written permission of FCE. 

No claim shall be considered if other than genuine parts supplied by FCE have been used. 

Products are only covered by this warranty in the country to where they were supplied by 

FCE.   

Warranty on products applies only to the original user of the equipment. 

This warranty shall not apply if the serial number or other identifying numbers or marks 

applied by FCE have been removed, defaced or are otherwise illegible. 

 

CLAIMS PROCEDURE 

Check that the goods are still under warranty before returning them to FCE (see above for 

warranty periods). 

Return the goods to FCE with an order number for the work to proceed.  If warranty is 

accepted no charge will be made.  If warranty is not accepted a quotation will be given for 

the repair  and  the  conditions under the section headed REPAIRS  and  ESTIMATES will 

apply. 

In the customer’s interest, goods must be accompanied by documentation detailing the 

nature of the fault or its symptoms.  Phrases such as ‘Faulty’ are unacceptable and will result 

in delays and possible charges to defray costs incurred in identifying the fault. 

In the case of hydraulic breakers and power packs, both the breaker and the pack should be 

returned. 

 

 

 

 

Содержание F14-35
















Отзывы: