background image

Greenlee Textron / Subsidiary of Textron Inc.

3

4455 Boeing Dr., Rockford, IL 61109-2988  815/397-7070

Chain Saws with Chain Brake

IMPORTANT SAFETY INFORMATION

This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury
or property damage. The signal word, defined below,
indicates the severity of the hazard. The message
after the signal word provides information for pre-
venting or avoiding the hazard.

Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.

Hazards which, if not avoided, COULD result in severe
injury or death.

Immediate hazards which, if not avoided, WILL result
in severe injury or death.

SAFETY
ALERT
SYMBOL

Skin injection hazard:

Oil under pressure easily punctures
skin causing serious injury, gan-
grene or death. If you are injured by
escaping oil, seek medical attention
immediately.

• Do not use hands to check for

leaks.

• Do not hold hose or couplers

while the hydraulic system is
pressurized.

• Depressurize the hydraulic

system before servicing.

Wear eye protection when operating
or servicing this tool.

Failure to wear eye protection can
result in serious eye injury from
flying debris or hydraulic oil.

Wear hearing protection when using
this tool.

Failure to observe this warning can
result in serious injury.

Wear foot protection when using this
tool.

Failure to observe this warning can
result in serious injury.

Read and understand all of the
instructions and safety information in
this manual before operating or
servicing this tool. Refer also to the
following manuals, which are listed
under Other Publications:

• Operation Manual

• Specifications and Parts Manual

Failure to observe this warning can
result in severe injury or death.

Содержание HPS513CB

















Отзывы: