Fagor CNC 8070, Руководство по программированию

Страница: 404 / 556

‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
Programming manual
402
CNC 8070
14.
CNC VARI
ABLES
Rel
a
ted
to
ax
is
m
a
ch
in
e pa
ra
m
e
te
rs
(S
OFT
V02.0
X
)
370
JOG MODE
Lin
Rot
Spd Ana Ser
(V.)[n].MPA.MANPOSSW.Xn Maximum positive travel with G201 Yes — Yes P/S
(V.)[n].MPA.MANNEGSW.Xn Maximum negative travel with G201 Yes — Yes P/S
(V.)[n].MPA.JOGFEED.Xn Continuous JOG mode feedrate Yes — Yes P/S
(V.)[n].MPA.JOGRAPFEED.Xn Rapid feed in continuous JOG mode Yes — Yes P/S
(V.)[n].MPA.MAXMANFEED.Xn Maximum feed in continuous JOG Yes — Yes P/S
(V.)[n].MPA.MAXMANACC.Xn Maximum acceleration in JOG mode Yes — Yes P/S
(V.)[n].MPA.MANFEEDP.Xn Maximum % of jog feedrate with G201 Yes — Yes P/S
(V.)[n].MPA.IPOFEEDP.Xn Maximum % of execution feedrate with G201 Yes — Yes P/S
(V.)[n].MPA.MANACCP.Xn Maximum % of jog acceleration with G201 Yes — Yes P/S
(V.)[n].MPA.IPOACCP.Xn Maximum % of execution acceleration with G201 Yes — Yes P/S
JOG MODE. HANDWHEELS
Lin Rot Spd Ana Ser
(V.)[n].MPA.MPGRESOL[i].Xn Dial resolution at the [i] position Yes Yes — Yes P/S
(V.)[n].MPA.MPGFILTER.Xn Filter time for the handwheel Yes Yes — Yes P/S
JOG MODE. INCREMENTAL JOG
Lin Rot Spd Ana Ser
(V.)[n].MPA.INCJOGDIST[i].Xn Moving distance at [i] dial position Yes Yes — Yes P/S
(V.)[n].MPA.INCJOGFEED[i].Xn Feedrate at [i] position Yes Yes — Yes P/S
LEADSCREW ERROR COMPENSATION
Lin Rot Spd Ana Ser
(V.)[n].MPA.LSCRWCOMP.Xn Leadscrew error compensation
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.NPOINTS.Xn Number of points in the table Yes Yes Yes Yes P/S
(V.)[n].MPA.TYPLSCRW.Xn Type of compensation
"0" = Real coordinates "1" = Theoretical
coordinates
Yes Yes Yes Yes P/S
(V.)[n].MPA.BIDIR.Xn Bi-directional compensation
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.REFNEED.Xn Mandatory home search
"0" = No "1"= Yes
Yes Yes Yes Yes P/S
(V.)[n].MPA.POSITION[i].Xn Master axis position for point [i] Yes Yes Yes Yes P/S
(V.)[n].MPA.POSERROR[i].Xn Error of point [i] in the positive direction Yes Yes Yes Yes P/S
(V.)[n].MPA.NEGERROR[i].Xn Error of point [i] in the negative direction Yes Yes Yes Yes P/S
FILTERS Lin Rot Spd Ana Ser
(V.)[n].MPA.ORDER[i].Xn Filter order Yes Yes Yes Yes P/S
(V.)[n].MPA.TYPE[i].Xn Type of filter
"1" = Low passing "2" = Anti-resonance
Yes Yes Yes Yes P/S
(V.)[n].MPA.FREQUENCY[i].Xn Break or center frequency Yes Yes Yes Yes P/S
(V.)[n].MPA.NORBWIDTH[i].Xn Normal bandwidth Yes Yes Yes Yes P/S
(V.)[n].MPA.SHARE[i].Xn % of signal going through the filter Yes Yes Yes Yes P/S
WORK SETS
Lin Rot Spd Ana Ser
(V.)[n].MPA.NPARSETS.Xn Number of work sets Yes Yes Yes Yes P/S
(V.)[n].MPA.DEFAULTSET.Xn Default work set (on power-up) Yes Yes Yes Yes P/S