background image

AC Brushless Servo Drive System Manual  Ver: 0002

ACa - 10 / 32

Preliminary

2.1

INTRODUCTION

The A.C.Servo drive is a compact speed drive which includes the power supply and is designed to
control a single Brushless ACS motor.
There are four modules of different power offering peak currents of 5, 10, 20 and 30 Amps -rms-
and whose main characteristics are:

- Three-phase power supply from Mains.
- Independent Power and Control supplies
- Dynamic braking in case of Mains fault.
- PWM  IGBTs.
- Incremental TTL Encoder feedback with 2500 ppt.
- Programmable encoder output 2/n (n, from 2 to 16)
- Velocity or Torque command.
- Velocity command filtered with ramps.
- Logic inputs to control the motor (Speed and Drive Enable).
- Galvanic isolation between power and control.
- Analog outputs to monitor speed and current.
- Control against excessive acceleration/deceleration.
- 7-segment display to monitor the status of the servo drive system.
- Internal fan activation depending on the Drive_Enable signal.
- Protection against feedback loss.
- Protection against excessive drive temperature.
- Protection against Bus overvoltage or undervoltage.
- i2t  protection in the motor.
- Protection of the internal Ballast resistor (i2t).
- Short-circuit protection in the motor output terminals.
- Protection against a phase drop.

A.C. Servodrive

Содержание ACS Series

































Отзывы: