12
Consult the designs in the front pages referenced in the text
by alphabet letters.
Closely follow the instructions set
out in this manual.
All responsibility, for any eventual
inconveniences, damages or fires caused by not complying
with the instructions in this manual, is declined.
The cooker hood must be placed at a minimum distance of 50 cm
from the cooking plane for electric cookers and 75cm for gas or
mixed cookers.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
The hood is equipped with a top air outlet
B
for discharge of fumes
to the outside (
Ducting version
exhaust pipe and pipe fixing
clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the hood can be used in the
filter version
, fitting an
activated carbon filter and the deflector
F
on the support (bracket)
G
, fumes and vapours are recycled through
the top grille
H
by means of an exhaust pipe connected to the top air
outlet
B
and the connection ring mounted on the deflector
F
(exhaust
pipe and pipe fixing clamps not provided).
The models with no suction motor only operate in ducting mode, and
must be connected to an external suction device (not supplied).
Expansion wall plugs are provided to secure the hood to most types
of walls/ceilings. However, a qualified technician must verify suitability
of the materials in accordance with the type of wall/ceiling. The wall/
ceiling must be strong enough to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Do not fix chimney flue to furniture or fly over shelves unless the
chimney flue can be easily removed, in case maintenance is ever
required.
Installation - Fig. 5-6-7
Preliminary information for installing the hood
Assembling the deflector (Fig. 6 - 3 parts only for filter version):
The three parts should be fixed with 2 screws, the deflector extension
is adjustable and should correspond to the width of the chimney flue
support, to which it is then fixed.
During electrical connection ensure the power supply is disconnected
at the domestic main switch.
1. Adjust extension of the hood support structure, as the final
height of the hood depends on this, and remember that with
installation completed the hood must be at least 50 cm above the
cook-top for electric cookers and 75 cm for gas or mixed
cookers.
2. a. Fix the two sections of the structure using 8 screws.
b. If the hood is provided with extensions longer than the
minimum, fit the reinforcement bracket S to the frame, using 4
screws.
3. Place the ceiling hole diagram directly above the cook-top (the
center of the diagram must match the center of the cook-top and
the edges must be parallel to the sides of the cook-top the side
of the diagram with the wording FRONT corresponds to the
control panel side). Prepare the electrical connection.
4. Drill as shown (6 holes for 6 wall plugs 4 plugs for fixture),
screw the outer screws leaving a space of about 1 cm. between
the screw head and the ceiling.
5. Fit an exhaust pipe inside the truss and connect it to the motor
compartment connection ring (exhaust pipe and fixing brackets
are not supplied).
6. Hook the frame onto the 4 screws (see step 4).
CAUTION! The side of the truss with connection box corresponds
to the side of the control panel with hood assembled.
7. Tighten the 4 screws.
8. Insert and tighten another 2 screws in the remaining free holes
for secure fixing.
9. Carry out the electrical connection to the mains power supply,
only turn on the power supply upon completion of assembly.
10. Hook the hood onto the truss, ensuring it fits properly to hook
the hood onto the truss partially tighten 4 screws (see also step
12).
11. Secure the hood to the truss using two screws; this will also help
center the two sections.
12. Tighten the 4 screws securing the truss to the hood.
13. For extractor versions (13A), connect the other end of the
exhaust pipe to the flue.
For filter versions (13F), fit deflector F to the truss and secure it
to the bracket supplied using 4 screws, then connect the
exhaust pipe to the connection ring located on the deflector.
14. Fit the nuts with fixing hooks supplied inside the top and bottom
sections of the flues at the rectangular slots. A total of 10 nuts
must be fitted.
15. Join the two top sections of the flue to cover the truss so that one
of the slots on the sections is situated on the same side of the
control panel and the other on the opposite side. Screw the two
sections together with 4 screws (2 each side- see the plan
diagram for joining the two sections).
16. Fix the top flue assembly to the truss, near the ceiling, with two
screws (one each side).
17. Carry out electrical connection of control panel and bulbs.
Warning! Make connections taking care to insert the
connectors in the right way.
18. Join the two bottom sections of the flue covering the truss using
6 screws (3 each side, see the plan diagram for joining the two
sections).
19. Insert the bottom section of the flue in its seat so that it
completely covers the motor compartment and electrical
connection box, then ensure it from inside the hood using two
screws.
20. Apply the 2 tabs (supplied) to cover the fixing points of the
bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE THE
NARROWER AND SHALLOWER ONES).
The wider and deeper tabs are those used for the top flue, and
must be cut to size.
21. Turn the mains power on again at the central electrical panel and
check for correct hood operation.
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.
