fadini Elpro 37, Руководство пользователя

Страница: 2 / 9

page 9
meccanica
FADINI
GB
IN CASE OF FAILURE PLEASE MAKE SURE THAT:
- Power supply to the electronic control board is 230V ±10% or 400V ±10%
- Power supply to the electric motor is 230V ±10% or 400V ±10%
- All of the fuses is all right
- The photocell contacts are closed
- No voltage drop has occurred from the Elpro board to the electric motor
- The limit switches are properly connected and work correctly
- All of the NC contacts of the control board are all right.
IMPORTANT FOR THE INSTALLATION AND THE CORRECT FUNCTIONING:
- The control box must be installed in a dry and sheltered place; suitable holes are provided with the FADINI universal box for fitting purpose and in
case any commercial box is used, this must be adequate to the job
- Make sure that power supply to the control board be
230V ±10% or 400V ±10%
- Make sure that power supply to the electric motor be 230V ±10% or 400V ±10%
- For distances longer than 50 metres increase the section of the wires
- Fit the mains to the control box with a high sensitivity, 0.03A, differential, magnetic-thermal circuit breaker
- Cables with 1.5mm² section wires are to be used for the power supply, electric motor and flasher for distances up to 50 m
- Cables with 1mm² section wires are to be used for the limit switches, photocells, push buttons and accessories
- If no photocells are used link out terminals 1 and 2
- If no stop button is used link out terminals 3 and 6
- Open/close motor run time trimmer must be always superior to the time actually required for the gate travel
N.W.: For applications such as light switching, CCTV, etc. use solid state relays to prevent the microprocessor from being affected
Diagnostic LEDs:
L ON =
Board on 230V or 400 V voltage and F1, F2, F3, F4, F5, F6 fuses all right
L0 OFF = Pedestrian mode, it switches on by any pedestrian pulsing
L1 ON = Pair photocells in closing not obstructed
L4 OFF =
Open, it switches on by any open pulse
L5 OFF = Close, it switches on by any close pulse
L6 ON = Stop, it switches off by any stop pulse
L7 OFF = Radio, it switches on by any pulse from the transmitter/radio contact
L8 ON = It switches off when Fc.C (limit switch closing = L-sw.C) is engaged, M1
L10 ON = It switches off when Fc.O. (limit switch opening = L-sw.O) is engaged, M1
L33 ON = Safety edge protecting closing not obstructed
L34 ON = Safety edge or photocell protecting opening not obstructed
ATTENTION: Before starting the electrical connections, check the voltage (230V or 400V) selector switch to be
set correctly.
In cases a motor with mechanical brake is used or a control board ELPRO 10 is to be changed, the
DIP-switch-A No.12 has to be in OFF.
!
Symbols
NC contact
NO contact
Led ON
Led OFF
Pilot light
Flasher
37
SINGLE – THREE PHASE ELECTRONIC CONTROL BOARD WITH ELECTRONIC BRAKE
FOR SLIDING GATE AUTOMATIC SYSTEMS WITH OR WITHOUT LIMIT SWITCHES
General description: the electronic control box ELPRO 37 has been developed to provide a reliable unit to control sliding gate automatic systems with
or without electronic brake and limit switches. Single-phase 230V 50/60Hz or Three-phase 400V 50/60Hz ELPRO 37 complies with the Low Voltage Norms
2006/95 CE and Electro-magnetic Compatibility 2004/108/CE. Installation is recommended by qualified technical installation agents in compliance with
the existing regulations. The manufacturer is not liable for any incorrect use of this appliance; and also reserves the right to change and update it without
previous notice.
ELECTRIC MOTOR
power supply
M1
L
TRANSFORMER
UNL
ON
OFF
1 2 3 4 5 6 7 8 9 10 11 12
DIP-SWITCH - A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PLUG-IN
RADIO
CARD
CONNECTOR
pedestrian
photocell
in closing
radio contact
common
open close stop
Indication lamp 24
V
ma
x 3
W
24
V
ac output
(ma
x load:
n°1 radio recei
v
er
n°3 pairs photocells
po
w
er suppl
y for
electric lock 15
V
A
ma
x
or indication lamp
230Vac OUTPUT for
flashing lamp
max 25W
Single-phase control board
power supply
230V - 50/60Hz ±10%
24V AC output
for photocell TX
enabling DSA control
NC
common
NEUTR
A
L
LI
V
E
26
27
28
CARD
CONNECTOR FOR
TRAFFIC LIGHTS
(Item 7282L)
+
_
Power supply
24V - 50mA max.
230V 400V
ON
OFF
1 2 3 4
DIP-SWITCH - B
ELPRO 3
7
UNL E 37
L0
L1 L4 L5 L6 L7 L8 L10
RUN TIME
0s - 120s
DWELL TIME
1s - 220s
PEDESTRIAN
1s - 45s
-
+
-
+
-
+
-
+
T.FUN
L33 L34
32 33 34
SAFETY EDGE
in OPENING
8,2 k
Ω
or NC
common
JA
1 2
SETUP
EDGE
TYPE
JB
1 2
Resistive contact
8,2 k
Ω
or NC
NOTE:
The green LEDs must
always be on.
L.s.O L.s. C
common 8,2 k
Ω or
NC
SAFETY EDGE
in CLOSING
ELECTRONIC BR
A
KE
INTENSIT
Y
1
2
4
5
3
F3=8
A
net
w
ork
F2=8
A
net
w
ork
F1=8
A
net
w
ork
16 17 18 19 20 21 22 23
F5=630
A
flashing
light protection
F4=2A transformer and
electronic brake
protection
38
39
F6=2A protection
24V
Three-phase control board
power supply
400V - 50/60Hz ±10%
LI
V
E
LI
V
E
LI
V
E
Capacitor for
single-phase motors
EARTH CONNECTION